AGA eR7 handset
showing 060-100
Codes from 060 to 100 report an open thermocouple circuit: the user panel gets no signal from one of the two sensors in a zone's probe.
Mon–Sat, 8am–8pm
- Temperature sensor
- Stove oven heating repair
- Source: AGA
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What 060-100
actually means.
Codes from 060 to 100 report an open thermocouple circuit: the user panel gets no signal from one of the two sensors in a zone's probe. Either the probe has failed or the four-wire plug behind the panel has worked partly loose.
AGA stove display
What to do when 060-100 shows on the stoveKind of codeTemperature sensor
The thin probe on the back wall of the oven sent the stove a reading it would not trust, or one that kept climbing past the setting. A loose plug behind the stove or a probe knocked against the racks is ruled out before the sensor or the board is replaced. If the oven keeps getting hotter with the controls turned off, switch the stove off at its breaker first.
Usually leads toStove oven heating repair
The oven part of a stove that stays cold, heats slowly or bakes too hot or too cool, fixed at the bake and broil elements, the oven igniter, the gas valve or the temperature sensor.
Shows up asStove Error Code
The stove shows letters and numbers, a flashing symbol or a short message, beeps, and the oven or a burner stops or will not start.
MakeAGA
A British name in home cooking, part of the Middleby group, best known for the cast-iron stove that stays warm all day.
SourceAGA eR7 field service manual, USA and Canada (AGA owner's guides library)
eR7 cookers; each thermocouple plug carries four wires, a pair for each of the probe's two sensors.
Before you book,
in this order.
Each step comes from AGA's own guidance for 060-100 on its stoves. Follow it to the end: the last card says whether this is a visit.
Write down the number shown on the handset.
Mention any recent work on the cooker, since a plug that was disturbed can cause this.
Book a visit; each wire pair on the plug is tested and the plug is checked for a firm fit.
Still there?
It usually turns into stove oven heating repair. Book with the code and the model number.
What not to do
An open-circuit code does not always mean a new probe is needed. AGA's own first check is whether the plug is pushed fully home, which costs nothing but a panel removal.
What you may
notice with it.
The stove problems 060-100 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Stove Error Code
8 causes, cheapest first
Where 060-100 usually leads
Stove oven heating repair.
AGA
stoves.
A British name in home cooking, part of the Middleby group, best known for the cast-iron stove that stays warm all day.
AGA stove repair
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
Heritage stove
Classic stoves built the old way, from AGA cast-iron heat storage stoves to French and Italian enamel stoves with brass trim, kept for decades and repaired rather than replaced.
In AGA's own words
T/Couple open circuit - Check the thermocouple with a multimeter.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. eR7 cookers; each thermocouple plug carries four wires, a pair for each of the probe's two sensors.
AGA 060-100 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about 060-100.
Can I clear 060-100 myself?
My AGA showed an open-circuit code after the panel was serviced. Could the plug be loose?
Will switching my AGA eR7 off and on clear a code in the 060 to 100 group?
Why does AGA list so many numbers for one kind of sensor problem?
Back to your everyday
Still showing 060-100?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.