AGA eR7 handset
showing 110-116
The main board in the base of an eR7 switches each element through a relay.
Mon–Sat, 8am–8pm
- Control board and power
- Control board and display repair
- Source: AGA
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What 110-116
actually means.
The main board in the base of an eR7 switches each element through a relay. Codes 110 to 116 mean one of those relays has shorted, so it may be holding power on when the control wants it off, and AGA's instruction is to reset and log the code, with a new board if it keeps returning.
AGA stove display
What to do when 110-116 shows on the stoveKind of codeControl board and power
The main board failed its own start-up check, lost contact with the display, or saw the supply voltage sag too low, often after a storm, a power outage or a spill that ran down behind the panel. The breaker, the cord and the outlet are ruled out before a board is replaced. A stove that sparks, smells of hot wiring or keeps heating while this code shows is switched off at the breaker first.
Usually leads toControl board and display repair
Stoves with a blank or flashing display, touch keys that do not answer, codes that keep returning or a stove that will not turn on, traced to the board, the keypad or the power to them.
Shows up asStove Error Code
The stove shows letters and numbers, a flashing symbol or a short message, beeps, and the oven or a burner stops or will not start.
MakeAGA
A British name in home cooking, part of the Middleby group, best known for the cast-iron stove that stays warm all day.
SourceAGA eR7 field service manual, USA and Canada (AGA owner's guides library)
eR7 cookers; the main board is housed in the base of the cooker.
Before you book,
in this order.
Each step comes from AGA's own guidance for 110-116 on its stoves. Follow it to the end: the last card says whether this is a visit.
Jot down the number and about what time it showed up.
Watch for a plate or oven that seems hotter than its setting, and tell the technician.
Book a visit: the technician resets the board, and if the same relay number returns, the main board is changed.
Still there?
It usually turns into control board and display repair. Book with the code and the model number.
What not to do
A relay code is not a problem with the plate or oven element itself. The element may be fine; it is the switch feeding it that has stuck.
What you may
notice with it.
The stove problems 110-116 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Stove Error Code
8 causes, cheapest first
Where 110-116 usually leads
Control board and display repair.
AGA
stoves.
A British name in home cooking, part of the Middleby group, best known for the cast-iron stove that stays warm all day.
AGA stove repairMore AGA codes
All 15 AGA codesControl board and power on other makes
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
Heritage stove
Classic stoves built the old way, from AGA cast-iron heat storage stoves to French and Italian enamel stoves with brass trim, kept for decades and repaired rather than replaced.
In AGA's own words
110 - 116: Relay short circuit - Reset PCB and Log. If recurring then PCB may be required.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. eR7 cookers; the main board is housed in the base of the cooker.
AGA 110-116 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about 110-116.
Can I clear 110-116 myself?
Can I reset the board on my AGA eR7 myself after a relay code?
Does a relay code on my AGA always mean a new board?
Why would a stuck relay make my AGA run too hot?
Back to your everyday
Still showing 110-116?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.