Electrolux stove shows F30 or F31
In Electrolux's wording, F30 is an open probe and F31 a shorted one.
Mon–Sat, 8am–8pm
- Temperature sensor
- Stove oven heating repair
- Source: Electrolux
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F30
actually means.
In Electrolux's wording, F30 is an open probe and F31 a shorted one. Either way the temperature reading is not usable, and the oven will not hold its heat.
Electrolux stove display · also shown as F31
What to do when F30 shows on the stoveKind of codeTemperature sensor
The thin probe on the back wall of the oven sent the stove a reading it would not trust, or one that kept climbing past the setting. A loose plug behind the stove or a probe knocked against the racks is ruled out before the sensor or the board is replaced. If the oven keeps getting hotter with the controls turned off, switch the stove off at its breaker first.
Usually leads toStove oven heating repair
The oven part of a stove that stays cold, heats slowly or bakes too hot or too cool, fixed at the bake and broil elements, the oven igniter, the gas valve or the temperature sensor.
Shows up asOven on My Stove Won't Heat Up
The burners on top work, but the oven underneath stays cold, heats only a little, or never reaches the temperature you set.
MakeElectrolux
A Swedish appliance group whose stoves in American kitchens often have their controls along the front edge.
SourceElectrolux: error code F30
For F30, the source is this: Electrolux's owner support code guide, written for its earlier electric models (the articles say Electric Ranges); the current ECF gas, dual fuel and induction stoves show Err with a number instead.
Before you book,
in this order.
Each step comes from Electrolux's own guidance for F30 on its stoves. Follow it to the end: the last card says whether this is a visit.
Take the stove off power for as long as 30 seconds.
Unplug a meat probe if one is in the oven, and try again.
A code that keeps returning calls for a visit to meter the oven sensor and its leads.
Still there?
It usually turns into stove oven heating repair. Book with the code and the model number.
What not to do
F30 and F31 are not overheating codes. They point at the sensor circuit, not at the heat itself.
What you may
notice with it.
The stove problems F30 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Where F30 usually leads
Stove oven heating repair.
Electrolux
stoves.
A Swedish appliance group whose stoves in American kitchens often have their controls along the front edge.
Electrolux stove repair
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In Electrolux's own words
Electric Range Error Code F30 - Open Probe
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. For F30, the source is this: Electrolux's owner support code guide, written for its earlier electric models (the articles say Electric Ranges); the current ECF gas, dual fuel and induction stoves show Err with a number instead.
Electrolux F30 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F30.
Can I clear F30 myself?
Is F31 on my Electrolux worse than F30?
Can I use my Electrolux burners while the oven shows F30?
Why did F30 appear on my Electrolux right after self-clean?
Back to your everyday
Still showing F30?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.