ZLINE induction stove
showing F/3
ZLINE fits a temperature sensor, called an NTC, to each induction coil.
Mon–Sat, 8am–8pm
- Temperature sensor
- Stove oven heating repair
- Source: ZLINE
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F/3
actually means.
ZLINE fits a temperature sensor, called an NTC, to each induction coil. F/3 says one of those sensors has failed or has lost its connection, so the control has no way to judge that coil's heat.
ZLINE stove display · also shown as F3
What to do when F/3 shows on the stoveKind of codeTemperature sensor
The thin probe on the back wall of the oven sent the stove a reading it would not trust, or one that kept climbing past the setting. A loose plug behind the stove or a probe knocked against the racks is ruled out before the sensor or the board is replaced. If the oven keeps getting hotter with the controls turned off, switch the stove off at its breaker first.
Usually leads toStove oven heating repair
The oven part of a stove that stays cold, heats slowly or bakes too hot or too cool, fixed at the bake and broil elements, the oven igniter, the gas valve or the temperature sensor.
Shows up asStove Error Code
The stove shows letters and numbers, a flashing symbol or a short message, beeps, and the oven or a burner stops or will not start.
MakeZLINE
ZLINE Kitchen and Bath, a younger American company whose stoves are often bought online.
SourceZLINE MINR and SINR induction stove user manual, April 2026 (ZLINE file store)
ZLINE MINR and SINR induction stoves; F/3 sits in the F group, which covers internal parts.
Before you book,
in this order.
Each step comes from ZLINE's own guidance for F/3 on its stoves. Follow it to the end: the last card says whether this is a visit.
Keep the zone with F/3 switched off.
Use other zones only if they work normally.
Book a visit; ZLINE tells owners not to attempt this repair themselves.
Still there?
It usually turns into stove oven heating repair. Book with the code and the model number.
What not to do
F/3 is not the same as E/1, which reports a coil running too hot. F/3 means the sensor itself has failed or come loose, so the control cannot read the coil at all.
What you may
notice with it.
The stove problems F/3 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Stove Error Code
8 causes, cheapest first
Where F/3 usually leads
Stove oven heating repair.
ZLINE
stoves.
ZLINE Kitchen and Bath, a younger American company whose stoves are often bought online.
ZLINE stove repair
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In ZLINE's own words
F/3 – NTC Sensor Failure
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. ZLINE MINR and SINR induction stoves; F/3 sits in the F group, which covers internal parts.
ZLINE F/3 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F/3.
Can I clear F/3 myself?
What is the NTC sensor behind F/3 on my ZLINE?
Can I use the rest of my ZLINE top with F/3 on one zone?
What is the difference between F/3 and E/5 on a ZLINE?
Back to your everyday
Still showing F/3?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.