ZLINE induction stove
showing F/1
F/1 on a ZLINE induction stove stands for one of two things: the main power board is not doing its job, or the control boards are no longer talking to each other.
Mon–Sat, 8am–8pm
- Control board and power
- Control board and display repair
- Source: ZLINE
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F/1
actually means.
F/1 on a ZLINE induction stove stands for one of two things: the main power board is not doing its job, or the control boards are no longer talking to each other. ZLINE points to an internal electronic failure or a loose wire as the reason.
ZLINE stove display · also shown as F1
What to do when F/1 shows on the stoveKind of codeControl board and power
The main board failed its own start-up check, lost contact with the display, or saw the supply voltage sag too low, often after a storm, a power outage or a spill that ran down behind the panel. The breaker, the cord and the outlet are ruled out before a board is replaced. A stove that sparks, smells of hot wiring or keeps heating while this code shows is switched off at the breaker first.
Usually leads toControl board and display repair
Stoves with a blank or flashing display, touch keys that do not answer, codes that keep returning or a stove that will not turn on, traced to the board, the keypad or the power to them.
Shows up asStove Error Code
The stove shows letters and numbers, a flashing symbol or a short message, beeps, and the oven or a burner stops or will not start.
MakeZLINE
ZLINE Kitchen and Bath, a younger American company whose stoves are often bought online.
SourceZLINE MINR and SINR induction stove user manual, April 2026 (ZLINE file store)
ZLINE MINR and SINR induction stoves (user manual dated April 2026).
Before you book,
in this order.
Each step comes from ZLINE's own guidance for F/1 on its stoves. Follow it to the end: the last card says whether this is a visit.
Switch the stove off at the circuit breaker.
Wait one minute, then switch the breaker back on and try again.
Book a visit if F/1 is back after the restart.
Still there?
It usually turns into control board and display repair. Book with the code and the model number.
What not to do
F/1 is not a problem with your pan or with one zone's coil. It concerns the boards that run the whole top, which is why every zone may stop at once.
What you may
notice with it.
The stove problems F/1 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Stove Error Code
8 causes, cheapest first
Where F/1 usually leads
Control board and display repair.
ZLINE
stoves.
ZLINE Kitchen and Bath, a younger American company whose stoves are often bought online.
ZLINE stove repair
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In ZLINE's own words
F/1 – Power Board Fault/
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. ZLINE MINR and SINR induction stoves (user manual dated April 2026).
ZLINE F/1 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F/1.
Can I clear F/1 myself?
My ZLINE induction stove showed F/1 once and then worked. Should I worry?
Why did all the zones on my ZLINE stop at once with F/1?
Can a loose connection inside my ZLINE bring up F/1?
Back to your everyday
Still showing F/1?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.