Electrolux stove shows F1
On Electrolux's earlier electric models, F1 means the control sees a shorted key pad.
Mon–Sat, 8am–8pm
- Knobs, keys and display
- Knob and switch replacement
- Source: Electrolux
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F1
actually means.
On Electrolux's earlier electric models, F1 means the control sees a shorted key pad. It may beep, ignore you or act as if a key were pressed.
Electrolux stove display
What to do when F1 shows on the stoveKind of codeKnobs, keys and display
A key on the panel was held down too long, reported a press nobody made, or stopped answering; or a knob's switch told the stove it was on when it was off. Water, a spill or grease worked in behind a knob is ruled out first, then the switch, the key panel and the cable to the board. If a burner keeps heating while the keys or knobs do nothing, switch the stove off at the breaker.
Usually leads toKnob and switch replacement
Stove knobs that are cracked, loose or spin in place, and the switches behind them that leave a burner stuck on high or dead, replaced at the knob, the stem or the switch.
Shows up asStove Display Blank or Flashing
The clock and display on the stove have gone dark, or they flash the time, a word or a string of characters and ignore the keys you press.
MakeElectrolux
A Swedish appliance group whose stoves in American kitchens often have their controls along the front edge.
SourceElectrolux: error code F1
For F1, the source is this: Electrolux's owner support code guide, written for its earlier electric models (the articles say Electric Ranges); the current ECF gas, dual fuel and induction stoves show Err with a number instead.
Before you book,
in this order.
Each step comes from Electrolux's own guidance for F1 on its stoves. Follow it to the end: the last card says whether this is a visit.
Wipe the key pad dry with a soft cloth.
Cut the supply for as long as 30 seconds, then turn it back on.
An F1 that shows again after drying and a reset needs a visit.
Still there?
It usually turns into knob and switch replacement. Book with the code and the model number.
What not to do
F1 on an Electrolux is not an oven or element problem. It is limited to the keypad and its connection.
What you may
notice with it.
The stove problems F1 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Stove Display Blank or Flashing
6 causes, cheapest first
Where F1 usually leads
Knob and switch replacement.
Electrolux
stoves.
A Swedish appliance group whose stoves in American kitchens often have their controls along the front edge.
Electrolux stove repair
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In Electrolux's own words
Electric Ranges Error Code F1 - Shorted Key Pad
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. For F1, the source is this: Electrolux's owner support code guide, written for its earlier electric models (the articles say Electric Ranges); the current ECF gas, dual fuel and induction stoves show Err with a number instead.
Electrolux F1 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F1.
Can I clear F1 myself?
Why does my Electrolux turn functions on by itself with F1 showing?
Could steam from a pot cause F1 on my Electrolux?
Does F1 on my Electrolux need a new board?
Back to your everyday
Still showing F1?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.