BlueStar stove
showing F50
Probe Error F50 on a BlueStar stove means a meat probe issue.
Mon–Sat, 8am–8pm
- Temperature sensor
- Stove oven heating repair
- Source: BlueStar
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F50
actually means.
Probe Error F50 on a BlueStar stove means a meat probe issue. The probe or its socket is not reading correctly.
BlueStar stove display · also shown as Probe Error F50
What to do when F50 shows on the stoveKind of codeTemperature sensor
The thin probe on the back wall of the oven sent the stove a reading it would not trust, or one that kept climbing past the setting. A loose plug behind the stove or a probe knocked against the racks is ruled out before the sensor or the board is replaced. If the oven keeps getting hotter with the controls turned off, switch the stove off at its breaker first.
Usually leads toStove oven heating repair
The oven part of a stove that stays cold, heats slowly or bakes too hot or too cool, fixed at the bake and broil elements, the oven igniter, the gas valve or the temperature sensor.
Shows up asOven on My Stove Runs Hot or Cold
Recipes take much longer or much less time than they should, cakes burn on the outside and stay raw inside, or an oven thermometer disagrees with the display by more than a little.
MakeBlueStar
A stove maker from Reading, Pennsylvania, whose gas burners are built to put out a lot of heat.
SourceBlueStar dual-fuel user manual 200009, Troubleshooting
BlueStar dual-fuel (BSDF) and Platinum induction (BSPIR) stoves with the oven touchscreen. No codes were confirmed for BlueStar's all-gas stoves.
Before you book,
in this order.
Each step comes from BlueStar's own guidance for F50 on its stoves. Follow it to the end: the last card says whether this is a visit.
Take the probe out and look for damage to the cable and plug.
Restart the oven without the probe.
If F50 shows with no probe in, book a visit.
Still there?
It usually turns into stove oven heating repair. Book with the code and the model number.
What not to do
The Remove Probe message is a separate prompt and nothing is broken when it shows. It just tells you the probe is still plugged in while Broil or Clean is selected.
What you may
notice with it.
The stove problems F50 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Oven on My Stove Runs Hot or Cold
7 causes, cheapest first
Where F50 usually leads
Stove oven heating repair.
BlueStar
stoves.
A stove maker from Reading, Pennsylvania, whose gas burners are built to put out a lot of heat.
BlueStar stove repair
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In BlueStar's own words
Probe Error F50
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. BlueStar dual-fuel (BSDF) and Platinum induction (BSPIR) stoves with the oven touchscreen. No codes were confirmed for BlueStar's all-gas stoves.
BlueStar F50 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F50.
Can I clear F50 myself?
My BlueStar says Remove Probe. Is that the same as F50?
Can I cook without the probe on my BlueStar stove after F50?
Why does Probe Error F50 show on my BlueStar stove with no probe plugged in?
Back to your everyday
Still showing F50?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.