BlueStar induction stove
showing E8
E8 on a BlueStar Platinum induction stove means a cooling fan issue in the stovetop.
Mon–Sat, 8am–8pm
- Control board and power
- Control board and display repair
- Source: BlueStar
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E8
actually means.
E8 on a BlueStar Platinum induction stove means a cooling fan issue in the stovetop. The induction electronics need that fan to stay cool.
BlueStar stove display
What to do when E8 shows on the stoveKind of codeControl board and power
The main board failed its own start-up check, lost contact with the display, or saw the supply voltage sag too low, often after a storm, a power outage or a spill that ran down behind the panel. The breaker, the cord and the outlet are ruled out before a board is replaced. A stove that sparks, smells of hot wiring or keeps heating while this code shows is switched off at the breaker first.
Usually leads toControl board and display repair
Stoves with a blank or flashing display, touch keys that do not answer, codes that keep returning or a stove that will not turn on, traced to the board, the keypad or the power to them.
Shows up asStovetop Not Heating
The burners on an electric, glass or induction stovetop stay cold or warm up only a little, sometimes all of them and sometimes two on one side, while the oven below may still work.
MakeBlueStar
A stove maker from Reading, Pennsylvania, whose gas burners are built to put out a lot of heat.
SourceBlueStar Platinum induction user manual 100799, Troubleshooting
BlueStar Platinum induction stoves (BSPIR); the codes show on the stovetop indicators.
Before you book,
in this order.
Each step comes from BlueStar's own guidance for E8 on its stoves. Follow it to the end: the last card says whether this is a visit.
Turn all zones off.
Make sure nothing blocks the air openings around the stove.
Book a visit; BlueStar sends E8 to service.
Still there?
It usually turns into control board and display repair. Book with the code and the model number.
What not to do
E8 is not the oven's cooling fan message, which is Fan Error F60 on the touchscreen. E8 appears on the stovetop indicators.
What you may
notice with it.
The stove problems E8 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Stovetop Not Heating
6 causes, cheapest first
Where E8 usually leads
Control board and display repair.
BlueStar
stoves.
A stove maker from Reading, Pennsylvania, whose gas burners are built to put out a lot of heat.
BlueStar stove repairMore BlueStar codes
Control board and power on other makes
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In BlueStar's own words
E8 is displayed
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. BlueStar Platinum induction stoves (BSPIR); the codes show on the stovetop indicators.
BlueStar E8 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E8.
Can I clear E8 myself?
Can I use my BlueStar induction stovetop with E8 showing?
Is E8 on my BlueStar stove the same as Fan Error F60?
What blocks the fan on a BlueStar induction stove?
Back to your everyday
Still showing E8?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.