BlueStar stove
showing F20
Control Error F20 on a BlueStar stove's oven touchscreen points to the control board or its wiring.
Mon–Sat, 8am–8pm
- Control board and power
- Control board and display repair
- Source: BlueStar
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F20
actually means.
Control Error F20 on a BlueStar stove's oven touchscreen points to the control board or its wiring. BlueStar gives no owner fix and sends it to service.
BlueStar stove display · also shown as Control Error F20
What to do when F20 shows on the stoveKind of codeControl board and power
The main board failed its own start-up check, lost contact with the display, or saw the supply voltage sag too low, often after a storm, a power outage or a spill that ran down behind the panel. The breaker, the cord and the outlet are ruled out before a board is replaced. A stove that sparks, smells of hot wiring or keeps heating while this code shows is switched off at the breaker first.
Usually leads toControl board and display repair
Stoves with a blank or flashing display, touch keys that do not answer, codes that keep returning or a stove that will not turn on, traced to the board, the keypad or the power to them.
Shows up asStove Display Blank or Flashing
The clock and display on the stove have gone dark, or they flash the time, a word or a string of characters and ignore the keys you press.
MakeBlueStar
A stove maker from Reading, Pennsylvania, whose gas burners are built to put out a lot of heat.
SourceBlueStar dual-fuel user manual 200009, Troubleshooting
BlueStar dual-fuel (BSDF) and Platinum induction (BSPIR) stoves with the oven touchscreen. No codes were confirmed for BlueStar's all-gas stoves.
Before you book,
in this order.
Each step comes from BlueStar's own guidance for F20 on its stoves. Follow it to the end: the last card says whether this is a visit.
Turn the oven off.
Switch the stove's breaker off and back on once to see whether the message clears.
If F20 returns, book a visit.
Still there?
It usually turns into control board and display repair. Book with the code and the model number.
What not to do
F20 is not a burner or gas problem. It concerns the electronics that run the oven.
What you may
notice with it.
The stove problems F20 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Where F20 usually leads
Control board and display repair.
BlueStar
stoves.
A stove maker from Reading, Pennsylvania, whose gas burners are built to put out a lot of heat.
BlueStar stove repairMore BlueStar codes
Control board and power on other makes
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In BlueStar's own words
Control Error F20
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. BlueStar dual-fuel (BSDF) and Platinum induction (BSPIR) stoves with the oven touchscreen. No codes were confirmed for BlueStar's all-gas stoves.
BlueStar F20 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F20.
Can I clear F20 myself?
Can I use the burners on my BlueStar stove with Control Error F20?
Is Control Error F20 always a new board on a BlueStar stove?
Does Control Error F20 mean the same thing on BlueStar dual-fuel and induction stoves?
Back to your everyday
Still showing F20?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.