BlueStar stove
showing F60
Fan Error F60 on a BlueStar stove points to a cooling fan issue.
Mon–Sat, 8am–8pm
- Control board and power
- Control board and display repair
- Source: BlueStar
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F60
actually means.
Fan Error F60 on a BlueStar stove points to a cooling fan issue. That fan keeps the controls cool and runs after the oven is off until it drops below 200°F.
BlueStar stove display · also shown as Fan Error F60
What to do when F60 shows on the stoveKind of codeControl board and power
The main board failed its own start-up check, lost contact with the display, or saw the supply voltage sag too low, often after a storm, a power outage or a spill that ran down behind the panel. The breaker, the cord and the outlet are ruled out before a board is replaced. A stove that sparks, smells of hot wiring or keeps heating while this code shows is switched off at the breaker first.
Usually leads toControl board and display repair
Stoves with a blank or flashing display, touch keys that do not answer, codes that keep returning or a stove that will not turn on, traced to the board, the keypad or the power to them.
Shows up asOven on My Stove Won't Heat Up
The burners on top work, but the oven underneath stays cold, heats only a little, or never reaches the temperature you set.
MakeBlueStar
A stove maker from Reading, Pennsylvania, whose gas burners are built to put out a lot of heat.
SourceBlueStar dual-fuel user manual 200009, Troubleshooting
BlueStar dual-fuel (BSDF) and Platinum induction (BSPIR) stoves with the oven touchscreen. No codes were confirmed for BlueStar's all-gas stoves.
Before you book,
in this order.
Each step comes from BlueStar's own guidance for F60 on its stoves. Follow it to the end: the last card says whether this is a visit.
Turn the oven off.
Listen for the fan behind the control panel; it normally runs after cooking until the oven cools.
Book a visit, since the manual gives no owner fix for F60.
Still there?
It usually turns into control board and display repair. Book with the code and the model number.
What not to do
A fan that keeps running after you turn the oven off is normal until the oven cools below 200°F. F60 means the fan is not working as it should.
What you may
notice with it.
The stove problems F60 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Oven on My Stove Won't Heat Up
6 causes, cheapest first
Where F60 usually leads
Control board and display repair.
BlueStar
stoves.
A stove maker from Reading, Pennsylvania, whose gas burners are built to put out a lot of heat.
BlueStar stove repairMore BlueStar codes
Control board and power on other makes
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In BlueStar's own words
Fan Error F60
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. BlueStar dual-fuel (BSDF) and Platinum induction (BSPIR) stoves with the oven touchscreen. No codes were confirmed for BlueStar's all-gas stoves.
BlueStar F60 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F60.
Can I clear F60 myself?
Why does the fan on my BlueStar stove keep running with the oven off?
Is it safe to bake with Fan Error F60 on my BlueStar stove?
Is Fan Error F60 the convection fan on my BlueStar stove?
Back to your everyday
Still showing F60?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.