Thermador induction stove shows F2 on one zone
Thermador's F2 means the electronics under the glass got too hot and the zone they feed was turned off.
Mon–Sat, 8am–8pm
- Stovetop elements
- Glass stovetop repair
- Source: Thermador
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F2
actually means.
Thermador's F2 means the electronics under the glass got too hot and the zone they feed was turned off. Blocked airflow or a long session on high is typical.
Thermador stove display · also shown as E7015
What to do when F2 shows on the stoveKind of codeStovetop elements
A burner on an electric or induction stovetop did not heat the way the knob or key asked, heated with nothing set, or ran hotter than the setting. The pan, a lock left on and the switch behind the knob are checked before the element under the glass, its limiter or an induction board is changed. If a burner keeps heating after it has been switched off, turn the stove's breaker off before anything else.
Usually leads toGlass stovetop repair
Smooth glass stovetops on electric and induction stoves with a cold circle, a cracked or chipped top, or a hot-surface light that stays on, repaired under the glass or with a new top.
Shows up asStovetop Not Heating
The burners on an electric, glass or induction stovetop stay cold or warm up only a little, sometimes all of them and sometimes two on one side, while the oven below may still work.
MakeThermador
A BSH luxury brand that began in Los Angeles; many owners know its gas stoves by the Star burner.
SourceThermador: ranges error codes
Where F2 is documented: Thermador's ranges code page, where these codes sit under its induction section; they apply to Thermador induction stoves.
Before you book,
in this order.
Each step comes from Thermador's own guidance for F2 on its stoves. Follow it to the end: the last card says whether this is a visit.
Leave the stove off long enough for the electronics to cool.
Touch any control element.
Once F2 goes out, cooking can go on; a visit is due if it becomes a habit.
What not to do
F2 is not the whole stovetop shutting down. That is F4; F2 affects the zone concerned.
What you may
notice with it.
The stove problems F2 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Stovetop Not Heating
6 causes, cheapest first
Where F2 usually leads
Glass stovetop repair.
Thermador
stoves.
A BSH luxury brand that began in Los Angeles; many owners know its gas stoves by the Star burner.
Thermador stove repairMore Thermador codes
Stovetop elements on other makes
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In Thermador's own words
The electronics have overheated. The corresponding cooking zone has been switched off.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Where F2 is documented: Thermador's ranges code page, where these codes sit under its induction section; they apply to Thermador induction stoves.
Thermador F2 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F2.
Can I clear F2 myself?
Why does F2 show on my Thermador only after long cooking?
Is E7015 the same as F2 on my Thermador?
Could a drawer below my Thermador cause F2?
Back to your everyday
Still showing F2?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.