Thermador induction stove shows E7010
Thermador uses E7010 when the stovetop cannot reach your home network or the matching hood it talks to.
Mon–Sat, 8am–8pm
- Knobs, keys and display
- Knob and switch replacement
- Source: Thermador
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E7010
actually means.
Thermador uses E7010 when the stovetop cannot reach your home network or the matching hood it talks to. Cooking itself does not depend on the link.
Thermador stove display
What to do when E7010 shows on the stoveKind of codeKnobs, keys and display
A key on the panel was held down too long, reported a press nobody made, or stopped answering; or a knob's switch told the stove it was on when it was off. Water, a spill or grease worked in behind a knob is ruled out first, then the switch, the key panel and the cable to the board. If a burner keeps heating while the keys or knobs do nothing, switch the stove off at the breaker.
Usually leads toKnob and switch replacement
Stove knobs that are cracked, loose or spin in place, and the switches behind them that leave a burner stuck on high or dead, replaced at the knob, the stem or the switch.
Shows up asStove Display Blank or Flashing
The clock and display on the stove have gone dark, or they flash the time, a word or a string of characters and ignore the keys you press.
MakeThermador
A BSH luxury brand that began in Los Angeles; many owners know its gas stoves by the Star burner.
SourceThermador: ranges error codes
Where E7010 is documented: Thermador's ranges code page, where these codes sit under its induction section; they apply to Thermador induction stoves.
Before you book,
in this order.
Each step comes from Thermador's own guidance for E7010 on its stoves. Follow it to the end: the last card says whether this is a visit.
Switch the stove off and on again; a one-time code will clear.
Check the home Wi-Fi and the hood's power.
If the code keeps coming back, note the exact code and book a visit.
Still there?
It usually turns into knob and switch replacement. Book with the code and the model number.
What not to do
E7010 is not a heating problem. The zones can heat even while the link is down.
What you may
notice with it.
The stove problems E7010 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Stove Display Blank or Flashing
6 causes, cheapest first
Where E7010 usually leads
Knob and switch replacement.
Thermador
stoves.
A BSH luxury brand that began in Los Angeles; many owners know its gas stoves by the Star burner.
Thermador stove repair
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In Thermador's own words
The cooktop is unable to connect to your home network (Wi-Fi) or to the hood.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Where E7010 is documented: Thermador's ranges code page, where these codes sit under its induction section; they apply to Thermador induction stoves.
Thermador E7010 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E7010.
Can I clear E7010 myself?
Can I cook on my Thermador with E7010 on the display?
Why does my Thermador hood not start by itself anymore?
My router changed and now my Thermador shows E7010. What should I do?
Back to your everyday
Still showing E7010?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.