GE Profile induction stove with a flashing power setting
On a Profile induction stove, a power setting that flashes instead of heating usually means the element cannot work with the pan: the pan is the wrong type, too small, off center or not flat on the glass.
Mon–Sat, 8am–8pm
- Stovetop elements
- Glass stovetop repair
- Source: GE Profile
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Flashing power setting
actually means.
On a Profile induction stove, a power setting that flashes instead of heating usually means the element cannot work with the pan: the pan is the wrong type, too small, off center or not flat on the glass. The manual also lists low voltage and a tripped breaker.
GE Profile stove display
What to do when Flashing power setting shows on the stoveKind of codeStovetop elements
A burner on an electric or induction stovetop did not heat the way the knob or key asked, heated with nothing set, or ran hotter than the setting. The pan, a lock left on and the switch behind the knob are checked before the element under the glass, its limiter or an induction board is changed. If a burner keeps heating after it has been switched off, turn the stove's breaker off before anything else.
Usually leads toGlass stovetop repair
Smooth glass stovetops on electric and induction stoves with a cold circle, a cracked or chipped top, or a hot-surface light that stays on, repaired under the glass or with a new top.
Shows up asStovetop Not Heating
The burners on an electric, glass or induction stovetop stay cold or warm up only a little, sometimes all of them and sometimes two on one side, while the oven below may still work.
MakeGE Profile
A GE Appliances line that sits a step above the plain GE stoves in features and finish.
SourceGE Profile owner's manual 49-2000990, induction front-control models
GE Profile induction front-control models (manual 49-2000990).
Before you book,
in this order.
Each step comes from GE Profile's own guidance for Flashing power setting on its stoves. Follow it to the end: the last card says whether this is a visit.
Center the pan on the cooking zone and check that its base sits flat on the glass.
Try a pan that a magnet sticks to, and one at least as wide as the element's minimum size.
If the setting still flashes with a suitable pan, reset the breaker and book a visit.
What not to do
A flashing power setting is not a broken element in most cases. The element is telling you the pan is the problem.
What you may
notice with it.
The stove problems Flashing power setting tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Stovetop Not Heating
6 causes, cheapest first
Where Flashing power setting usually leads
Glass stovetop repair.
GE Profile
stoves.
A GE Appliances line that sits a step above the plain GE stoves in features and finish.
GE Profile stove repair
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Electric stove
A stove that runs entirely on electricity through a heavy cord and a large outlet behind it, with coil burners that lift out or a smooth glass stovetop with elements under it.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In GE Profile's own words
Surface units do not work properly or flashing power setting.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. GE Profile induction front-control models (manual 49-2000990).
GE Profile Flashing power setting stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Flashing power setting.
Can I clear Flashing power setting myself?
Why does the number flash on my Profile induction burner when I set a small pot on it?
My old pots worked on gas. Why does my Profile induction flash with them?
Can a warped pan make my Profile induction setting flash?
Back to your everyday
Still showing Flashing power setting?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.