SKS dual-fuel stove induction knob
showing F33~F45
On SKS dual-fuel stoves with an induction section next to the gas burners, that section reports its control errors on the knob's LED ring as F33 through F45.
Mon–Sat, 8am–8pm
- Stovetop elements
- Glass stovetop repair
- Source: SKS
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F33~F45
actually means.
On SKS dual-fuel stoves with an induction section next to the gas burners, that section reports its control errors on the knob's LED ring as F33 through F45. SKS attaches a single meaning to all of them: an electronic control error.
SKS stove display · also shown as F33-F45
What to do when F33~F45 shows on the stoveKind of codeStovetop elements
A burner on an electric or induction stovetop did not heat the way the knob or key asked, heated with nothing set, or ran hotter than the setting. The pan, a lock left on and the switch behind the knob are checked before the element under the glass, its limiter or an induction board is changed. If a burner keeps heating after it has been switched off, turn the stove's breaker off before anything else.
Usually leads toGlass stovetop repair
Smooth glass stovetops on electric and induction stoves with a cold circle, a cracked or chipped top, or a hot-surface light that stays on, repaired under the glass or with a new top.
Shows up asStove Error Code
The stove shows letters and numbers, a flashing symbol or a short message, beeps, and the oven or a burner stops or will not start.
MakeSKS
Signature Kitchen Suite, the luxury built-in brand from LG.
SourceSKS Pro dual-fuel stove owner's manual MFL68920528 (sksappliances.com)
SKS 36- and 48-inch dual-fuel Pro stoves with sous vide and induction (manual MFL68920528).
Before you book,
in this order.
Each step comes from SKS's own guidance for F33~F45 on its stoves. Follow it to the end: the last card says whether this is a visit.
Clear the display by turning the induction knob to its center OFF position.
Try the induction zone again.
Note the number and book a visit if the code shows up again.
What not to do
An F33 to F45 code does not involve the gas burners or the oven. It comes from the induction section alone, so the rest of the stove may work normally.
What you may
notice with it.
The stove problems F33~F45 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Stove Error Code
8 causes, cheapest first
Where F33~F45 usually leads
Glass stovetop repair.
SKS
stoves.
Signature Kitchen Suite, the luxury built-in brand from LG.
SKS stove repairMore SKS codes
Stovetop elements on other makes
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In SKS's own words
Induction control beeps and LED on knob displays F33~F45 error code.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. SKS 36- and 48-inch dual-fuel Pro stoves with sous vide and induction (manual MFL68920528).
SKS F33~F45 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F33~F45.
Can I clear F33~F45 myself?
Can I cook on the gas burners while my SKS induction knob shows F40?
How do I clear a knob code on the SKS induction section?
Why does my SKS dual-fuel stove use F33 and up for induction?
Back to your everyday
Still showing F33~F45?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.