GE stove
showing ERR
GE shows ERR when the pads were pressed in an order or with a value the oven cannot use, such as a temperature outside its range.
Mon–Sat, 8am–8pm
- Knobs, keys and display
- Knob and switch replacement
- Source: GE
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What ERR
actually means.
GE shows ERR when the pads were pressed in an order or with a value the oven cannot use, such as a temperature outside its range. It is an entry mistake, not a part failure.
GE stove display
What to do when ERR shows on the stoveKind of codeKnobs, keys and display
A key on the panel was held down too long, reported a press nobody made, or stopped answering; or a knob's switch told the stove it was on when it was off. Water, a spill or grease worked in behind a knob is ruled out first, then the switch, the key panel and the cable to the board. If a burner keeps heating while the keys or knobs do nothing, switch the stove off at the breaker.
Usually leads toKnob and switch replacement
Stove knobs that are cracked, loose or spin in place, and the switches behind them that leave a burner stuck on high or dead, replaced at the knob, the stem or the switch.
Shows up asStove Display Blank or Flashing
The clock and display on the stove have gone dark, or they flash the time, a word or a string of characters and ignore the keys you press.
MakeGE
GE Appliances, owned by Haier, makes some of the most common stoves in American kitchens.
SourceGE Appliances support: oven error and function code list
GE ranges and stoves with an electronic oven control. GE says its list covers the most common codes, not every code on every past and present model.
Before you book,
in this order.
Each step comes from GE's own guidance for ERR on its stoves. Follow it to the end: the last card says whether this is a visit.
Press Cancel/Off to clear the entry.
Set the oven again one step at a time: mode, temperature, then Start.
If ERR appears on every entry, even simple ones, reset the breaker and book a visit to check the keypanel.
Still there?
It usually turns into knob and switch replacement. Book with the code and the model number.
What not to do
ERR is not a request for service on its own. Only an ERR that shows up no matter what you enter points at the keypanel.
What you may
notice with it.
The stove problems ERR tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Stove Display Blank or Flashing
6 causes, cheapest first
Where ERR usually leads
Knob and switch replacement.
GE
stoves.
GE Appliances, owned by Haier, makes some of the most common stoves in American kitchens.
GE stove repair
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Electric stove
A stove that runs entirely on electricity through a heavy cord and a large outlet behind it, with coil burners that lift out or a smooth glass stovetop with elements under it.
In GE's own words
ERR means that there has been an invalid entry when setting the oven controls.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. GE ranges and stoves with an electronic oven control. GE says its list covers the most common codes, not every code on every past and present model.
GE ERR stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about ERR.
Can I clear ERR myself?
Why does my GE stove say ERR when I set 550 degrees?
Can a sticky pad cause ERR on a GE?
Is ERR the same on a GE as the F codes?
Back to your everyday
Still showing ERR?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.