Miele stove oven says no signal to the probe
Miele's wireless food probe sends its reading to the oven by radio.
Mon–Sat, 8am–8pm
- Temperature sensor
- Stove oven heating repair
- Source: Miele
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What No signal to the probe
actually means.
Miele's wireless food probe sends its reading to the oven by radio. The message means the oven is not receiving it. Miele warns that a microwave working close by can drown out the probe, since both use nearly the same radio band.
Miele stove display
What to do when No signal to the probe shows on the stoveKind of codeTemperature sensor
The thin probe on the back wall of the oven sent the stove a reading it would not trust, or one that kept climbing past the setting. A loose plug behind the stove or a probe knocked against the racks is ruled out before the sensor or the board is replaced. If the oven keeps getting hotter with the controls turned off, switch the stove off at its breaker first.
Usually leads toStove oven heating repair
The oven part of a stove that stays cold, heats slowly or bakes too hot or too cool, fixed at the bake and broil elements, the oven igniter, the gas valve or the temperature sensor.
Shows up asOven on My Stove Runs Hot or Cold
Recipes take much longer or much less time than they should, cakes burn on the outside and stay raw inside, or an oven thermometer disagrees with the display by more than a little.
MakeMiele
A German family-owned company whose stoves pair gas burners with detailed electronic oven controls.
SourceMiele operating instructions, 30-inch dual fuel range
For No signal to the probe, the source is this: Printed in the frequently asked questions of Miele's operating instructions for the 30-inch dual fuel stove (HR 1924-3 G DF family).
Before you book,
in this order.
Each step comes from Miele's own guidance for No signal to the probe on its stoves. Follow it to the end: the last card says whether this is a visit.
Push the probe into the food again at a new spot.
Turn off any microwave running nearby while you use the probe.
If the probe is still not recognized, it may be the probe itself; a new probe is sold through Miele's dealers.
Still there?
It usually turns into stove oven heating repair. Book with the code and the model number.
What not to do
This message is not a problem with the oven's own temperature sensor. The oven still heats; only the probe reading is missing.
What you may
notice with it.
The stove problems No signal to the probe tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Oven on My Stove Runs Hot or Cold
7 causes, cheapest first
Where No signal to the probe usually leads
Stove oven heating repair.
Miele
stoves.
A German family-owned company whose stoves pair gas burners with detailed electronic oven controls.
Miele stove repair
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In Miele's own words
In some cases, reception interference can even be caused by a microwave operating in the vicinity of the oven
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. For No signal to the probe, the source is this: Printed in the frequently asked questions of Miele's operating instructions for the 30-inch dual fuel stove (HR 1924-3 G DF family).
Miele No signal to the probe stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about No signal to the probe.
Can I clear No signal to the probe myself?
Why does my Miele lose the probe signal when the microwave is on?
Can I finish cooking on my Miele without the probe?
How do I know if my Miele probe is broken?
Back to your everyday
Still showing No signal to the probe?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.