Dacor stove
showing C-A2
C-A2 on a Dacor pro stove means the cooling motor is operating abnormally.
Mon–Sat, 8am–8pm
- Control board and power
- Control board and display repair
- Source: Dacor
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What C-A2
actually means.
C-A2 on a Dacor pro stove means the cooling motor is operating abnormally. Its job is to keep oven heat away from the electronics.
Dacor stove display
What to do when C-A2 shows on the stoveKind of codeControl board and power
The main board failed its own start-up check, lost contact with the display, or saw the supply voltage sag too low, often after a storm, a power outage or a spill that ran down behind the panel. The breaker, the cord and the outlet are ruled out before a board is replaced. A stove that sparks, smells of hot wiring or keeps heating while this code shows is switched off at the breaker first.
Usually leads toControl board and display repair
Stoves with a blank or flashing display, touch keys that do not answer, codes that keep returning or a stove that will not turn on, traced to the board, the keypad or the power to them.
Shows up asOven on My Stove Won't Heat Up
The burners on top work, but the oven underneath stays cold, heats only a little, or never reaches the temperature you set.
MakeDacor
A luxury cooking brand owned by Samsung, found in kitchens that wanted a professional look.
SourceDacor DOP30T840GS gas stove user manual, Information codes
Dacor Transitional pro stoves with the tilting touch panel; the gas DOP30T840GS and dual-fuel DOP36P86DLS manuals print the same table.
Before you book,
in this order.
Each step comes from Dacor's own guidance for C-A2 on its stoves. Follow it to the end: the last card says whether this is a visit.
Turn the oven off.
Listen for the fan the next time the oven runs, and note any silence or grinding.
Book a visit; Dacor lists no owner reset for C-A2.
Still there?
It usually turns into control board and display repair. Book with the code and the model number.
What not to do
The fan that circulates heat around your food is a different part. It is the cooling motor behind the panels.
What you may
notice with it.
The stove problems C-A2 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Oven on My Stove Won't Heat Up
6 causes, cheapest first
Where C-A2 usually leads
Control board and display repair.
Dacor
stoves.
A luxury cooking brand owned by Samsung, found in kitchens that wanted a professional look.
Dacor stove repairMore Dacor codes
Control board and power on other makes
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In Dacor's own words
The cooling motor is operating abnormally.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Dacor Transitional pro stoves with the tilting touch panel; the gas DOP30T840GS and dual-fuel DOP36P86DLS manuals print the same table.
Dacor C-A2 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about C-A2.
Can I clear C-A2 myself?
My Dacor stove is noisier than usual and shows C-A2. Why?
Can I bake with C-A2 showing on my Dacor stove?
Is the fan I hear after cooking on my Dacor stove the one C-A2 is about?
Back to your everyday
Still showing C-A2?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.