Bosch freestanding stove shows E100
Bosch describes E100 simply as an electronics problem on its freestanding stoves.
Mon–Sat, 8am–8pm
- Control board and power
- Control board and display repair
- Source: Bosch
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E100
actually means.
Bosch describes E100 simply as an electronics problem on its freestanding stoves. It is a broad code, so the first step is the same long breaker reset used for the other e-codes.
Bosch stove display
What to do when E100 shows on the stoveKind of codeControl board and power
The main board failed its own start-up check, lost contact with the display, or saw the supply voltage sag too low, often after a storm, a power outage or a spill that ran down behind the panel. The breaker, the cord and the outlet are ruled out before a board is replaced. A stove that sparks, smells of hot wiring or keeps heating while this code shows is switched off at the breaker first.
Usually leads toControl board and display repair
Stoves with a blank or flashing display, touch keys that do not answer, codes that keep returning or a stove that will not turn on, traced to the board, the keypad or the power to them.
Shows up asStove Display Blank or Flashing
The clock and display on the stove have gone dark, or they flash the time, a word or a string of characters and ignore the keys you press.
MakeBosch
A German appliance maker, part of BSH, whose stoves are usually the slide-in kind that sits level with the counter.
SourceBosch: freestanding range error codes
E100 is listed here: Bosch's freestanding range code page, listed for both its electric and gas freestanding models.
Before you book,
in this order.
Each step comes from Bosch's own guidance for E100 on its stoves. Follow it to the end: the last card says whether this is a visit.
Switch the breaker off and wait five minutes.
Restore the breaker and run a short test bake.
Book a visit if E100 returns, and note what the stove was doing when it appeared.
Still there?
It usually turns into control board and display repair. Book with the code and the model number.
What not to do
E100 is not a named part. It flags the electronics as a whole, and testing narrows it down.
What you may
notice with it.
The stove problems E100 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Where E100 usually leads
Control board and display repair.
Bosch
stoves.
A German appliance maker, part of BSH, whose stoves are usually the slide-in kind that sits level with the counter.
Bosch stove repairMore Bosch codes
All 15 Bosch codesControl board and power on other makes
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Electric stove
A stove that runs entirely on electricity through a heavy cord and a large outlet behind it, with coil burners that lift out or a smooth glass stovetop with elements under it.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In Bosch's own words
An electronics fault has occurred.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. E100 is listed here: Bosch's freestanding range code page, listed for both its electric and gas freestanding models.
Bosch E100 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E100.
Can I clear E100 myself?
E100 on my Bosch cleared after the breaker reset. Is that the end of it?
What should I tell a technician about E100 on my Bosch?
Is E100 on a Bosch linked to a power surge?
Back to your everyday
Still showing E100?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.