Bosch induction stove shows E9011
E9011 means Bosch's induction slide-in is not connected to the power supply as its circuit diagram requires.
Mon–Sat, 8am–8pm
- Control board and power
- Control board and display repair
- Source: Bosch
Book a visit
Three short steps, about a minute.
or call (844) 415-7620
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E9011
actually means.
E9011 means Bosch's induction slide-in is not connected to the power supply as its circuit diagram requires. It usually appears after a new install or a move.
Bosch stove display
What to do when E9011 shows on the stoveKind of codeControl board and power
The main board failed its own start-up check, lost contact with the display, or saw the supply voltage sag too low, often after a storm, a power outage or a spill that ran down behind the panel. The breaker, the cord and the outlet are ruled out before a board is replaced. A stove that sparks, smells of hot wiring or keeps heating while this code shows is switched off at the breaker first.
Usually leads toControl board and display repair
Stoves with a blank or flashing display, touch keys that do not answer, codes that keep returning or a stove that will not turn on, traced to the board, the keypad or the power to them.
Shows up asStove Won't Turn On
Nothing happens anywhere on the stove: no burner heats, the oven stays cold, the clock and lights are dark, or the display lights up but nothing will start.
MakeBosch
A German appliance maker, part of BSH, whose stoves are usually the slide-in kind that sits level with the counter.
SourceBosch: slide-in range error codes
Where E9011 is documented: Bosch's slide-in range code page, listed under induction slide-in models.
Before you book,
in this order.
Each step comes from Bosch's own guidance for E9011 on its stoves. Follow it to the end: the last card says whether this is a visit.
Switch the breaker off.
Have the installer or an electrician check the connection against the stove's circuit diagram.
Book a visit if the wiring is right and E9011 remains.
Still there?
It usually turns into control board and display repair. Book with the code and the model number.
What not to do
E9011 is not a component failure inside the stove. It points at how the stove was wired in.
What you may
notice with it.
The stove problems E9011 tends to arrive with. Answer these at the stove before anyone is booked.
All problems
Where E9011 usually leads
Control board and display repair.
Bosch
stoves.
A German appliance maker, part of BSH, whose stoves are usually the slide-in kind that sits level with the counter.
Bosch stove repairMore Bosch codes
All 15 Bosch codesControl board and power on other makes
Gas stove
A stove with gas burners on top, whether its oven below runs on gas too or on electricity, fed by one gas line behind it and plugged into a wall outlet for the spark.
Electric stove
A stove that runs entirely on electricity through a heavy cord and a large outlet behind it, with coil burners that lift out or a smooth glass stovetop with elements under it.
Induction stove
A stove with a flat glass top that heats the pan itself through a magnetic field, run by touch keys and power boards, with an electric oven underneath.
In Bosch's own words
The appliance is not connected properly.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Where E9011 is documented: Bosch's slide-in range code page, listed under induction slide-in models.
Bosch E9011 stove repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E9011.
Can I clear E9011 myself?
My Bosch showed E9011 right after installation. Whose job is it?
Can I use my Bosch with E9011 if some zones work?
Why did E9011 appear on my Bosch after a kitchen remodel?
Back to your everyday
Still showing E9011?
Book with the code written exactly as the stove shows it, the full model number, and whether you notice any smell of gas or hot wiring — when there is a code, that is where the diagnosis starts.