---
title: "Stove Error Codes — What They Mean | StoveRepair.center"
description: "What the letters and numbers on a stove display are telling you: which ones are only a lock or a setting, which ones name a part that failed, and how to check…"
url: "https://stoverepair.center/error-codes/"
---

Error codes

# Stove error codes, read properly.

A code narrows the search and is also the thing most often read wrong: the same characters mean different things on different brands, and a fair number of the codes people look up are not failures at all — they are modes the appliance was left in.

## Find your code, make by make.

Type the characters exactly as the display shows them, or pick the make. Each code has a page of its own: what it means on that brand, what to check, and what not to do.

### AGA stove error codes 15 codes

- [FE Knobs, keys and display The small processor inside the eR7's touch panel has stopped responding.](https://stoverepair.center/error-codes/aga-fe/)
- [CE Control board and power The touch panel is sending commands and the main board in the base is not answering.](https://stoverepair.center/error-codes/aga-ce/)
- [S Mode, not a failure The roasting and baking ovens are in slumber mode, idling at a lower heat.](https://stoverepair.center/error-codes/aga-s/)
- [007 Temperature sensor The user panel can no longer read the heat sensors in the plates and ovens.](https://stoverepair.center/error-codes/aga-007/)
- [010-014 Oven heating A plate or oven ran at full power and still took too long to reach its heat.](https://stoverepair.center/error-codes/aga-010-014/)
- [020-024 Temperature sensor The two sensors inside one zone's heat probe no longer agree.](https://stoverepair.center/error-codes/aga-020-024/)
- [060-100 Temperature sensor The panel has lost the signal from one of a zone's heat sensors.](https://stoverepair.center/error-codes/aga-060-100/)
- [110-116 Control board and power A relay that powers one of the elements is stuck closed on the main board.](https://stoverepair.center/error-codes/aga-110-116/)
- [130-136 Oven heating The electronic switch feeding one element has seen a problem in that circuit.](https://stoverepair.center/error-codes/aga-130-136/)
- [139 Knobs, keys and display The user panel behind the top left door has become too hot.](https://stoverepair.center/error-codes/aga-139/)
- [159 Knobs, keys and display The radio receiver inside the cooker is not talking to the main board.](https://stoverepair.center/error-codes/aga-159/)
- [E2 Stovetop elements The electronics under the induction glass have run too hot.](https://stoverepair.center/error-codes/aga-e2/)
- [U400 Control board and power The stove has been wired to the supply incorrectly.](https://stoverepair.center/error-codes/aga-u400/)
- [Er Stovetop elements The induction top is reporting an internal problem the owner cannot fix.](https://stoverepair.center/error-codes/aga-er/)
- [H Mode, not a failure The zone you switched off is still hot.](https://stoverepair.center/error-codes/aga-h/)

[AGA stove repair](https://stoverepair.center/brands/aga/)

### Bosch stove error codes 15 codes

- [e005 Control board and power Bosch's touch display can no longer reach the board that powers the heat.](https://stoverepair.center/error-codes/bosch-e005/)
- [e011 Knobs, keys and display One of the touch sensors on the oven's panel has stopped reading.](https://stoverepair.center/error-codes/bosch-e011/)
- [E100 Control board and power The electronics reported a general problem.](https://stoverepair.center/error-codes/bosch-e100/)
- [e101 Temperature sensor Bosch reports that the stove's temperature sensor is misbehaving.](https://stoverepair.center/error-codes/bosch-e101/)
- [e126 Door lock Bosch's Self Clean latch is not doing its job.](https://stoverepair.center/error-codes/bosch-e126/)
- [E302 Control board and power Heat has built up in the control panel or in the power board.](https://stoverepair.center/error-codes/bosch-e302/)
- [e310 Control board and power The power supply to the stove has failed.](https://stoverepair.center/error-codes/bosch-e310/)
- [ERR/toP Mode, not a failure A zone on top was switched on while Self Clean was running.](https://stoverepair.center/error-codes/bosch-err-top/)
- [dE Mode, not a failure Demo mode has been switched on.](https://stoverepair.center/error-codes/bosch-de/)
- [E9000 Control board and power The stove sees too much or too little voltage coming in.](https://stoverepair.center/error-codes/bosch-e9000/)
- [E9011 Control board and power The stove is not connected properly.](https://stoverepair.center/error-codes/bosch-e9011/)
- [F1 Stovetop elements A cooking zone overheated and turned itself off.](https://stoverepair.center/error-codes/bosch-f1/)
- [F2 Stovetop elements The induction electronics overheated.](https://stoverepair.center/error-codes/bosch-f2/)
- [F5 Stovetop elements Hot cookware is sitting near the control panel.](https://stoverepair.center/error-codes/bosch-f5/)
- [F8 Mode, not a failure A zone ran a long time without any touch and switched itself off.](https://stoverepair.center/error-codes/bosch-f8/)

[Bosch stove repair](https://stoverepair.center/brands/bosch/)

### LG stove error codes 15 codes

- [F1 Temperature sensor The temperature sensor in the upper or only oven is giving a bad reading.](https://stoverepair.center/error-codes/lg-f1/)
- [F4 Temperature sensor The temperature sensor in the lower oven is reading wrong.](https://stoverepair.center/error-codes/lg-f4/)
- [F3 Knobs, keys and display A key on the touch pad is reading as pressed or wet.](https://stoverepair.center/error-codes/lg-f3/)
- [F9 Oven heating The oven is not reaching or holding the heat you set.](https://stoverepair.center/error-codes/lg-f9/)
- [F10 Door lock The oven door lock did not do what the control asked.](https://stoverepair.center/error-codes/lg-f10/)
- [F11 Control board and power Two of the stove's electronic boards lost contact.](https://stoverepair.center/error-codes/lg-f11/)
- [F17 Oven heating The fan that moves hot air inside the oven is not turning as it should.](https://stoverepair.center/error-codes/lg-f17/)
- [F27 Control board and power The cooling fan stalled or locked while the oven was cleaning.](https://stoverepair.center/error-codes/lg-f27/)
- [F33 Stovetop elements A temperature sensor under a front induction zone is reading wrong.](https://stoverepair.center/error-codes/lg-f33/)
- [F42 Control board and power The stove is seeing a supply voltage it does not like.](https://stoverepair.center/error-codes/lg-f42/)
- [F8 Temperature sensor The oven has a problem reading its meat probe.](https://stoverepair.center/error-codes/lg-f8/)
- [F51 Stovetop elements The griddle zone's sensor or heating is not working as it should.](https://stoverepair.center/error-codes/lg-f51/)
- [HS Mode, not a failure The stovetop is still too hot to touch.](https://stoverepair.center/error-codes/lg-hs/)
- [PF Mode, not a failure The power to the stove was cut for a moment.](https://stoverepair.center/error-codes/lg-pf/)
- [Sb Mode, not a failure The stove is in Sabbath mode.](https://stoverepair.center/error-codes/lg-sb/)

[LG stove repair](https://stoverepair.center/brands/lg/)

### Samsung stove error codes 15 codes

- [C-20 Temperature sensor The oven can no longer trust what its temperature sensor is telling it.](https://stoverepair.center/error-codes/samsung-c-20/)
- [C-21 Oven heating The control saw the oven getting hotter than it should.](https://stoverepair.center/error-codes/samsung-c-21/)
- [C-24 Oven heating Heat in the oven is rising faster than normal, most often because the vent is covered.](https://stoverepair.center/error-codes/samsung-c-24/)
- [C-25 Oven heating The gas oven did not warm up the way the control expected.](https://stoverepair.center/error-codes/samsung-c-25/)
- [C-30 Control board and power The temperature sensor on the main control board reads wrong, or the board itself is running hot.](https://stoverepair.center/error-codes/samsung-c-30/)
- [C-d0 Knobs, keys and display The control thinks one of its keys is stuck or shorted.](https://stoverepair.center/error-codes/samsung-c-d0/)
- [C-d1 Door lock The lock that holds the oven door has drifted out of line.](https://stoverepair.center/error-codes/samsung-c-d1/)
- [C-F0 Control board and power Two electronic boards inside the stove stopped talking to each other.](https://stoverepair.center/error-codes/samsung-c-f0/)
- [bAd LinE Control board and power The power cord is not wired to the stove the right way.](https://stoverepair.center/error-codes/samsung-bad-line/)
- [tESt Mode, not a failure The stove is in Demo mode, the store-floor setting that turns off the heat.](https://stoverepair.center/error-codes/samsung-test/)
- [-dE- Mode, not a failure The oven divider for split cooking is missing, loose or in the wrong slot.](https://stoverepair.center/error-codes/samsung-de/)
- [door Door lock The control reads the oven door as open.](https://stoverepair.center/error-codes/samsung-door/)
- [Cooktop in use Mode, not a failure Self Clean is blocked because a burner or element on top is still on.](https://stoverepair.center/error-codes/samsung-cooktop-in-use/)
- [Underlined u Stovetop elements The zone on your induction stove cannot find a usable pan.](https://stoverepair.center/error-codes/samsung-underlined-u/)
- [C-10 Mode, not a failure A self-diagnosis in the SmartThings app started with the oven too hot or too cold.](https://stoverepair.center/error-codes/samsung-c-10/)

[Samsung stove repair](https://stoverepair.center/brands/samsung/)

### Wolf stove error codes 15 codes

- [01 Door lock The oven door lock motor ran, but the control never felt the lock reach its position.](https://stoverepair.center/error-codes/wolf-01/)
- [02 Oven heating The oven got hotter than Wolf's safety limit allows.](https://stoverepair.center/error-codes/wolf-02/)
- [03 Temperature sensor The oven temperature sensor reads as an open circuit.](https://stoverepair.center/error-codes/wolf-03/)
- [04 Temperature sensor The oven temperature sensor circuit reads as shorted.](https://stoverepair.center/error-codes/wolf-04/)
- [09 Temperature sensor The control sees the meat probe as shorted.](https://stoverepair.center/error-codes/wolf-09/)
- [0E Oven heating A power relay for an oven element is stuck closed.](https://stoverepair.center/error-codes/wolf-0e/)
- [10 Control board and power A power surge or outage upset the oven control.](https://stoverepair.center/error-codes/wolf-10/)
- [PF Mode, not a failure The stove had a power failure, or the oven is too hot for the mode you chose.](https://stoverepair.center/error-codes/wolf-pf/)
- [ERR OC Knobs, keys and display The oven knob lost contact with the oven control.](https://stoverepair.center/error-codes/wolf-err-oc/)
- [0221 Oven heating The relay that feeds the bake or convection element in the right or single oven reads as shorted.](https://stoverepair.center/error-codes/wolf-0221/)
- [3C20 Control board and power The stove is getting a higher voltage than it should.](https://stoverepair.center/error-codes/wolf-3c20/)
- [5521 Control board and power The main cooling fan is turning too slowly or has stalled.](https://stoverepair.center/error-codes/wolf-5521/)
- [E2 Stovetop elements An induction coil under the glass got too hot.](https://stoverepair.center/error-codes/wolf-e2/)
- [E6 Control board and power The induction stovetop sees a problem with its electrical supply.](https://stoverepair.center/error-codes/wolf-e6/)
- [U400 Control board and power The induction stovetop is reading too much voltage.](https://stoverepair.center/error-codes/wolf-u400/)

[Wolf stove repair](https://stoverepair.center/brands/wolf/)

### GE stove error codes 14 codes

- [F1 Knobs, keys and display GE links F1 to the touch keypanel on the front of the stove, and the fix is often a new keypanel.](https://stoverepair.center/error-codes/ge-f1/)
- [F2 Oven heating The oven got hotter than GE's preset limit, and the control could not tell why.](https://stoverepair.center/error-codes/ge-f2/)
- [F3 Temperature sensor GE reads F3 as an oven sensor that usually has to be replaced.](https://stoverepair.center/error-codes/ge-f3/)
- [F5 Control board and power GE points F5 at the electronic oven control itself.](https://stoverepair.center/error-codes/ge-f5/)
- [F9 Door lock Something in the oven door lock circuit has failed.](https://stoverepair.center/error-codes/ge-f9/)
- [FF Control board and power GE says FF usually means the electronic control needs replacing.](https://stoverepair.center/error-codes/ge-ff/)
- [F96 Control board and power An internal component in the oven's electronics needs replacing.](https://stoverepair.center/error-codes/ge-f96/)
- [Bad Line Control board and power The stove has power but it was wired wrong.](https://stoverepair.center/error-codes/ge-bad-line/)
- [Unlock Door Door lock The oven door did not unlock after a self-clean cycle.](https://stoverepair.center/error-codes/ge-unlock-door/)
- [Loc Door Door lock The door lock is flashing even though nobody chose self-clean.](https://stoverepair.center/error-codes/ge-loc-door/)
- [LOC Mode, not a failure The control lockout is on, so the oven will not start.](https://stoverepair.center/error-codes/ge-loc/)
- [ERR Knobs, keys and display The oven was given a setting it cannot accept.](https://stoverepair.center/error-codes/ge-err/)
- [OFF Mode, not a failure The oven is still too hot to start what you asked for.](https://stoverepair.center/error-codes/ge-off/)
- [⊃ Mode, not a failure The oven is set to Sabbath Mode.](https://stoverepair.center/error-codes/ge-backward-c/)

[GE stove repair](https://stoverepair.center/brands/ge/)

### JennAir stove error codes 14 codes

- [F1E1 Control board and power The oven control, or the wiring to it, has a problem.](https://stoverepair.center/error-codes/jennair-f1e1/)
- [F2E0 Knobs, keys and display The keypad or touch panel is reporting a problem.](https://stoverepair.center/error-codes/jennair-f2e0/)
- [F3E0 Temperature sensor The oven temperature sensor circuit is reading wrong.](https://stoverepair.center/error-codes/jennair-f3e0/)
- [F3E4 Temperature sensor The oven is not reading the meat probe properly.](https://stoverepair.center/error-codes/jennair-f3e4/)
- [F5E0 Door lock Something at the oven door, the latch or its switch, is not reporting correctly.](https://stoverepair.center/error-codes/jennair-f5e0/)
- [F5E5 Oven heating The oven did not reach self-clean heat within 30 minutes.](https://stoverepair.center/error-codes/jennair-f5e5/)
- [F7E0 Door lock The oven door latch assembly or its wiring has a problem.](https://stoverepair.center/error-codes/jennair-f7e0/)
- [F8E0 Control board and power The oven cooling fan is running too slowly.](https://stoverepair.center/error-codes/jennair-f8e0/)
- [F9-1 Door lock The door latch or the door lock switch has a problem.](https://stoverepair.center/error-codes/jennair-f9-1/)
- [F0E0 Control board and power The oven control found a problem it cannot identify.](https://stoverepair.center/error-codes/jennair-f0e0/)
- [F6E1 Control board and power The appliance manager, or its wiring, is reporting a problem.](https://stoverepair.center/error-codes/jennair-f6e1/)
- [C81 Stovetop elements The stovetop cooking area overheated and shut itself off.](https://stoverepair.center/error-codes/jennair-c81/)
- [ES Mode, not a failure The display went dark to save power; it is a setting.](https://stoverepair.center/error-codes/jennair-es/)
- [Blinking amber lights Knobs, keys and display Amber lights and a tone mean the stove has stored an error code.](https://stoverepair.center/error-codes/jennair-blinking-amber-lights/)

[JennAir stove repair](https://stoverepair.center/brands/jennair/)

### Kenmore stove error codes 14 codes

- [Er- Control board and power The oven control has logged a function error.](https://stoverepair.center/error-codes/kenmore-er/)
- [E0 Temperature sensor The circuit that measures oven temperature has failed.](https://stoverepair.center/error-codes/kenmore-e0/)
- [E1 Oven heating The oven starts heating but the temperature rises very slowly.](https://stoverepair.center/error-codes/kenmore-e1/)
- [E2 Door lock The oven door switch is not being detected properly.](https://stoverepair.center/error-codes/kenmore-e2/)
- [E3 Oven heating The oven cannot heat at all.](https://stoverepair.center/error-codes/kenmore-e3/)
- [E5 Oven heating The oven went above 650 degrees during normal cooking.](https://stoverepair.center/error-codes/kenmore-e5/)
- [E8 Control board and power The display board and the main control board are not talking to each other.](https://stoverepair.center/error-codes/kenmore-e8/)
- [E10 Door lock The oven door cannot be locked or unlocked.](https://stoverepair.center/error-codes/kenmore-e10/)
- [E16 Door lock The door lock is not holding the door securely.](https://stoverepair.center/error-codes/kenmore-e16/)
- [E17 Control board and power The circuit that checks cooling fan speed has a problem.](https://stoverepair.center/error-codes/kenmore-e17/)
- [E02 Temperature sensor The temperature sensor has an error.](https://stoverepair.center/error-codes/kenmore-e02/)
- [E03 Oven heating The oven got too hot and shut itself off.](https://stoverepair.center/error-codes/kenmore-e03/)
- [H Stovetop elements A cooking zone is still too hot to touch.](https://stoverepair.center/error-codes/kenmore-h/)
- [LOC Door lock The control panel is locked.](https://stoverepair.center/error-codes/kenmore-loc/)

[Kenmore stove repair](https://stoverepair.center/brands/kenmore/)

### Whirlpool stove error codes 14 codes

- [C81 Stovetop elements A cooking area on the stovetop got too hot and the stove shut it off on purpose.](https://stoverepair.center/error-codes/whirlpool-c81/)
- [H Mode, not a failure A cooking area is still too hot to touch, even though it is off.](https://stoverepair.center/error-codes/whirlpool-h/)
- [F2 E1 Knobs, keys and display Whirlpool first asks you to check the grates, then points at the control panel.](https://stoverepair.center/error-codes/whirlpool-f2-e1/)
- [FEE6 Oven heating The bake element in the main oven, or its wiring, has a problem.](https://stoverepair.center/error-codes/whirlpool-fee6/)
- [FEE7 Oven heating The broil element at the top of the main oven, or its wiring, has a problem.](https://stoverepair.center/error-codes/whirlpool-fee7/)
- [F3 E0 Temperature sensor The oven temperature sensor, the control or the wiring between them has a problem.](https://stoverepair.center/error-codes/whirlpool-f3-e0/)
- [F5 E5 Oven heating The oven did not reach cleaning temperature within 30 minutes.](https://stoverepair.center/error-codes/whirlpool-f5-e5/)
- [F8 E0 Control board and power The cooling fan is running too slowly.](https://stoverepair.center/error-codes/whirlpool-f8-e0/)
- [F1 E7 Control board and power The appliance control board, or the wiring to it, has a problem.](https://stoverepair.center/error-codes/whirlpool-f1-e7/)
- [F6 E5 Knobs, keys and display The user interface, the panel you press, or its wiring has a problem.](https://stoverepair.center/error-codes/whirlpool-f6-e5/)
- [PUSH Mode, not a failure The oven is waiting for you to press Start.](https://stoverepair.center/error-codes/whirlpool-push/)
- [Lo Mode, not a failure The oven is preheating and still below 170 degrees.](https://stoverepair.center/error-codes/whirlpool-lo/)
- [Flashing indicator light Knobs, keys and display On a glass stovetop, one or more touch keys are reading as held down.](https://stoverepair.center/error-codes/whirlpool-flashing-indicator-light/)
- [DEMO MODE Mode, not a failure The stove is in store demonstration mode, so the oven will not heat.](https://stoverepair.center/error-codes/whirlpool-demo-mode/)

[Whirlpool stove repair](https://stoverepair.center/brands/whirlpool/)

### Hestan stove error codes 12 codes

- [ERR04 Control board and power A non-critical electronic problem; the oven can still run without the affected feature.](https://stoverepair.center/error-codes/hestan-err04/)
- [ER01 Ignition and burners The Smart Burner did not see the pan heating up.](https://stoverepair.center/error-codes/hestan-er01/)
- [ER04 Mode, not a failure Power to the stove was lost during a cooking cycle.](https://stoverepair.center/error-codes/hestan-er04/)
- [ER05 Ignition and burners The burner did not light after several tries, so the cycle stopped.](https://stoverepair.center/error-codes/hestan-er05/)
- [ER06 Control board and power A problem not listed elsewhere; the cooking cycle has ended.](https://stoverepair.center/error-codes/hestan-er06/)
- [Er 03 Knobs, keys and display Something is sitting on the touch controls.](https://stoverepair.center/error-codes/hestan-er-03/)
- [Er 47 Control board and power The touch controls and the induction generator stopped communicating.](https://stoverepair.center/error-codes/hestan-er-47/)
- [E2 Stovetop elements The induction coils overheated.](https://stoverepair.center/error-codes/hestan-e2/)
- [E6 Control board and power The power board or its supply has a problem.](https://stoverepair.center/error-codes/hestan-e6/)
- [E8 Control board and power A cooling fan is spinning at the wrong speed.](https://stoverepair.center/error-codes/hestan-e8/)
- [E9 Temperature sensor One coil has lost its heat sensor.](https://stoverepair.center/error-codes/hestan-e9/)
- [U 400 Control board and power The supply voltage at the stove is too high.](https://stoverepair.center/error-codes/hestan-u-400/)

[Hestan stove repair](https://stoverepair.center/brands/hestan/)

### Maytag stove error codes 12 codes

- [1c1c Knobs, keys and display The keypad or its wiring has a problem.](https://stoverepair.center/error-codes/maytag-1c1c/)
- [3d11 Temperature sensor The oven temperature sensor, the control or the wiring has a problem.](https://stoverepair.center/error-codes/maytag-3d11/)
- [F8 E2 Control board and power The cooling fan is spinning faster than it should.](https://stoverepair.center/error-codes/maytag-f8-e2/)
- [ES Mode, not a failure Energy Save mode is on, so the display goes dark when the stove is idle.](https://stoverepair.center/error-codes/maytag-es/)
- [Lock Knobs, keys and display The stovetop control lock is on.](https://stoverepair.center/error-codes/maytag-lock/)
- [Call Service Control board and power The control detected an error and wants it looked at.](https://stoverepair.center/error-codes/maytag-call-service/)
- [F9-1 Door lock The door latch, the door lock switch or the wiring has a problem.](https://stoverepair.center/error-codes/maytag-f9-1/)
- [F7 E0 Door lock The oven door latch assembly or its wiring has a problem.](https://stoverepair.center/error-codes/maytag-f7-e0/)
- [Sab Mode, not a failure Sabbath Mode is on; only Bake works and the display stays quiet.](https://stoverepair.center/error-codes/maytag-sab/)
- [Probe Mode, not a failure The oven is waiting for the meat probe to be plugged in.](https://stoverepair.center/error-codes/maytag-probe/)
- [4d21 Control board and power The cooling fan is running too slowly.](https://stoverepair.center/error-codes/maytag-4d21/)
- [POWER LOSS Mode, not a failure Power was cut, and the clock needs to be set again.](https://stoverepair.center/error-codes/maytag-power-loss/)

[Maytag stove repair](https://stoverepair.center/brands/maytag/)

### Dacor stove error codes 11 codes

- [C-d0 Knobs, keys and display For a whole minute, the stove has read one of its keys as held down.](https://stoverepair.center/error-codes/dacor-c-d0/)
- [C-d1 Door lock The lock on the oven door has stopped in the wrong place.](https://stoverepair.center/error-codes/dacor-c-d1/)
- [C-F0 Control board and power Two boards inside the stove have lost their link.](https://stoverepair.center/error-codes/dacor-c-f0/)
- [C-F2 Knobs, keys and display The touch screen is no longer connected to the main board.](https://stoverepair.center/error-codes/dacor-c-f2/)
- [C-20 Temperature sensor The sensor that tells the oven how hot it is has an open or shorted reading.](https://stoverepair.center/error-codes/dacor-c-20/)
- [C-21 Oven heating The oven's internal temperature climbed abnormally high.](https://stoverepair.center/error-codes/dacor-c-21/)
- [C-23 Temperature sensor The plug-in food probe is reading as a short circuit.](https://stoverepair.center/error-codes/dacor-c-23/)
- [C-31 Control board and power The control board itself is running too hot.](https://stoverepair.center/error-codes/dacor-c-31/)
- [C-A2 Control board and power The cooling motor is not running as it should.](https://stoverepair.center/error-codes/dacor-c-a2/)
- [C-24 Oven heating Something is covering an oven vent or air path.](https://stoverepair.center/error-codes/dacor-c-24/)
- [C-70 Temperature sensor The steam sensor reads as open or shorted.](https://stoverepair.center/error-codes/dacor-c-70/)

[Dacor stove repair](https://stoverepair.center/brands/dacor/)

### KitchenAid stove error codes 11 codes

- [Blinking amber lights Control board and power Amber lights that blink with a tone mean the stove has logged an error code.](https://stoverepair.center/error-codes/kitchenaid-blinking-amber-lights/)
- [F0E0 Mode, not a failure The self-check found no error.](https://stoverepair.center/error-codes/kitchenaid-f0e0/)
- [Blinking Start button Mode, not a failure Start was pressed too soon, before it began flashing.](https://stoverepair.center/error-codes/kitchenaid-blinking-start-button/)
- [Solid Start light Mode, not a failure Sabbath Mode is on.](https://stoverepair.center/error-codes/kitchenaid-solid-start-light/)
- [F9E0 Control board and power KitchenAid sends this one to an electrician to check the power supply.](https://stoverepair.center/error-codes/kitchenaid-f9e0/)
- [F2 E0 Knobs, keys and display The keypad, the control or the wiring between them has a problem.](https://stoverepair.center/error-codes/kitchenaid-f2-e0/)
- [F3 E3 Temperature sensor The oven temperature sensor or its wiring has a problem.](https://stoverepair.center/error-codes/kitchenaid-f3-e3/)
- [F7 E5 Control board and power The cooling fan or its wiring has a problem.](https://stoverepair.center/error-codes/kitchenaid-f7-e5/)
- [F5 E0 Door lock The door latch, the door switch or the wiring has a problem.](https://stoverepair.center/error-codes/kitchenaid-f5-e0/)
- [1c31 Control board and power The oven control or its wiring has a problem.](https://stoverepair.center/error-codes/kitchenaid-1c31/)
- [LOC Door lock The control lock is on, so the pads and the oven door are locked.](https://stoverepair.center/error-codes/kitchenaid-loc/)

[KitchenAid stove repair](https://stoverepair.center/brands/kitchenaid/)

### Thermador stove error codes 10 codes

- [E Control board and power The oven control found a problem and is showing a numbered code.](https://stoverepair.center/error-codes/thermador-e/)
- [E0211 Control board and power An over-the-air update from Home Connect stalled partway.](https://stoverepair.center/error-codes/thermador-e0211/)
- [dE Mode, not a failure Demo mode is switched on.](https://stoverepair.center/error-codes/thermador-de/)
- [E7010 Knobs, keys and display The stove cannot connect to your Wi-Fi or to the hood.](https://stoverepair.center/error-codes/thermador-e7010/)
- [E9000 Control board and power The supply voltage is incorrect.](https://stoverepair.center/error-codes/thermador-e9000/)
- [F1 Stovetop elements A cooking zone overheated.](https://stoverepair.center/error-codes/thermador-f1/)
- [F2 Stovetop elements Heat in the electronics made Thermador shut one zone down.](https://stoverepair.center/error-codes/thermador-f2/)
- [F4 Stovetop elements Heat under the glass shut down the whole stovetop.](https://stoverepair.center/error-codes/thermador-f4/)
- [F5 Stovetop elements A hot pan is near the control panel.](https://stoverepair.center/error-codes/thermador-f5/)
- [F8 Mode, not a failure A zone ran too long without any touch and switched off.](https://stoverepair.center/error-codes/thermador-f8/)

[Thermador stove repair](https://stoverepair.center/brands/thermador/)

### BlueStar stove error codes 9 codes

- [F20 Control board and power BlueStar traces this to the control board or the wires connected to it.](https://stoverepair.center/error-codes/bluestar-f20/)
- [F40 Temperature sensor BlueStar reports trouble with the sensor that reads oven heat.](https://stoverepair.center/error-codes/bluestar-f40/)
- [F50 Temperature sensor BlueStar reports trouble with the meat probe or its socket.](https://stoverepair.center/error-codes/bluestar-f50/)
- [F60 Control board and power BlueStar reports trouble with the fan that cools the controls.](https://stoverepair.center/error-codes/bluestar-f60/)
- [F80 Oven heating The oven has a high temperature problem.](https://stoverepair.center/error-codes/bluestar-f80/)
- [E2 Stovetop elements The induction stovetop overheated.](https://stoverepair.center/error-codes/bluestar-e2/)
- [E6 Control board and power The stove is getting too little voltage, or the stovetop system has a problem.](https://stoverepair.center/error-codes/bluestar-e6/)
- [E8 Control board and power The stovetop cooling fan has a problem.](https://stoverepair.center/error-codes/bluestar-e8/)
- [Er47 Control board and power The induction stovetop reports an internal system problem.](https://stoverepair.center/error-codes/bluestar-er47/)

[BlueStar stove repair](https://stoverepair.center/brands/bluestar/)

### Frigidaire stove error codes 9 codes

- [F1 Knobs, keys and display One of the keys on the control pad reads as shorted.](https://stoverepair.center/error-codes/frigidaire-f1/)
- [F3 Control board and power The stove's control boards stopped communicating.](https://stoverepair.center/error-codes/frigidaire-f3/)
- [F10 Oven heating The oven is running hotter than it should.](https://stoverepair.center/error-codes/frigidaire-f10/)
- [F12 Control board and power The electronic control failed a self-check of its own chip.](https://stoverepair.center/error-codes/frigidaire-f12/)
- [F13 Control board and power The memory chip on the control board did not read correctly.](https://stoverepair.center/error-codes/frigidaire-f13/)
- [F30 Temperature sensor Frigidaire's control sees the oven probe's circuit as broken.](https://stoverepair.center/error-codes/frigidaire-f30/)
- [F31 Temperature sensor Frigidaire's control sees the oven probe's wires as touching.](https://stoverepair.center/error-codes/frigidaire-f31/)
- [F40 Stovetop elements The control has locked out the stovetop.](https://stoverepair.center/error-codes/frigidaire-f40/)
- [F90 Door lock Something in the oven door's locking motor or switch has gone wrong.](https://stoverepair.center/error-codes/frigidaire-f90/)

[Frigidaire stove repair](https://stoverepair.center/brands/frigidaire/)

### Electrolux stove error codes 8 codes

- [Err Control board and power The stove found a problem and is showing a numbered code for the technician.](https://stoverepair.center/error-codes/electrolux-err/)
- [5d Mode, not a failure Demo mode is on, so the stove runs its display but makes no heat.](https://stoverepair.center/error-codes/electrolux-5d/)
- [F10 Oven heating The oven sensed heat above its safe range and stopped.](https://stoverepair.center/error-codes/electrolux-f10/)
- [F30 Temperature sensor The probe circuit reads as broken or as shorted.](https://stoverepair.center/error-codes/electrolux-f30/)
- [F90 Door lock The oven door lock reported a problem.](https://stoverepair.center/error-codes/electrolux-f90/)
- [F3 Control board and power Signals between the control parts were lost.](https://stoverepair.center/error-codes/electrolux-f3/)
- [F1 Knobs, keys and display A key on the touch pad reads as shorted.](https://stoverepair.center/error-codes/electrolux-f1/)
- [F40 Stovetop elements The control locked out the elements on top.](https://stoverepair.center/error-codes/electrolux-f40/)

[Electrolux stove repair](https://stoverepair.center/brands/electrolux/)

### GE Profile stove error codes 8 codes

- [F4 Temperature sensor The oven temperature sensor on a Profile stove has given a reading the control cannot use.](https://stoverepair.center/error-codes/ge-profile-f4/)
- [F6 Knobs, keys and display GE ties F6 to the touch keypanel, which often needs replacing.](https://stoverepair.center/error-codes/ge-profile-f6/)
- [F8 Control board and power The electronic oven control on the Profile is reporting a problem with itself.](https://stoverepair.center/error-codes/ge-profile-f8/)
- [FC Door lock A part in the oven door lock circuit has failed.](https://stoverepair.center/error-codes/ge-profile-fc/)
- [F350 Control board and power The upper cooling fan circuit has a problem, or something is blocking the fan.](https://stoverepair.center/error-codes/ge-profile-f350/)
- [Flashing power setting Stovetop elements The induction element is not happy with the pan on it.](https://stoverepair.center/error-codes/ge-profile-flashing-power-setting/)
- [DOOR LOCKING Door lock Self-clean was chosen, but the oven door is not closed.](https://stoverepair.center/error-codes/ge-profile-door-locking/)
- [HOT Mode, not a failure The oven is too warm to start a steam clean.](https://stoverepair.center/error-codes/ge-profile-hot/)

[GE Profile stove repair](https://stoverepair.center/brands/ge-profile/)

### ILVE stove error codes 8 codes

- [E9 Temperature sensor A sensor that reads the heat of one induction coil is damaged.](https://stoverepair.center/error-codes/ilve-e9/)
- [E47 Control board and power Either the zone display or the power card behind it is damaged.](https://stoverepair.center/error-codes/ilve-e47/)
- [E5 Control board and power The power card that drives the induction coils is defective.](https://stoverepair.center/error-codes/ilve-e5/)
- [E Stovetop elements The induction top has detected an external problem and may have switched off.](https://stoverepair.center/error-codes/ilve-e/)
- [F Control board and power Something inside the stove needs attention, according to the induction control.](https://stoverepair.center/error-codes/ilve-f/)
- [U Mode, not a failure Either no suitable pan is on the zone, or the knob is on the food-warming setting.](https://stoverepair.center/error-codes/ilve-u/)
- [H Mode, not a failure You switched the zone off, but it has not cooled yet.](https://stoverepair.center/error-codes/ilve-h/)
- [LLLL Mode, not a failure The key lock is on and every zone is switched off.](https://stoverepair.center/error-codes/ilve-llll/)

[ILVE stove repair](https://stoverepair.center/brands/ilve/)

### Miele stove error codes 8 codes

- [F32 Door lock Miele's Self Clean lock never closed.](https://stoverepair.center/error-codes/miele-f32/)
- [F33 Door lock Miele's Self Clean lock will not release the door.](https://stoverepair.center/error-codes/miele-f33/)
- [Demo Mode Mode, not a failure Demo mode is on, so the oven's heating does not work.](https://stoverepair.center/error-codes/miele-demo-mode/)
- [Maximum operating duration reached Mode, not a failure The oven ran so long that its safety shut-off stopped it.](https://stoverepair.center/error-codes/miele-maximum-operating-duration-reached/)
- [Power failure - Program cancelled Mode, not a failure A brief power cut stopped the cooking program.](https://stoverepair.center/error-codes/miele-power-failure-program-cancelled/)
- [System Lock Mode, not a failure Miele's System Lock is switched on.](https://stoverepair.center/error-codes/miele-system-lock/)
- [No signal to the probe Temperature sensor The oven cannot pick up its wireless food probe.](https://stoverepair.center/error-codes/miele-no-signal-to-the-probe/)
- [12:00 Mode, not a failure The stove went without power for over 150 hours.](https://stoverepair.center/error-codes/miele-12-00/)

[Miele stove repair](https://stoverepair.center/brands/miele/)

### SKS stove error codes 8 codes

- [F1~F25 Control board and power The oven's electronic control has found a problem somewhere in its circuits.](https://stoverepair.center/error-codes/sks-f1-f25/)
- [F1~F15 Stovetop elements The induction control has reported an electronic error on a knob's LED ring.](https://stoverepair.center/error-codes/sks-f1-f15/)
- [F33~F45 Stovetop elements The induction section beside the gas burners has an electronic control error.](https://stoverepair.center/error-codes/sks-f33-f45/)
- [F51~F59 Stovetop elements The griddle's own control has reported an electronic error.](https://stoverepair.center/error-codes/sks-f51-f59/)
- [F62 Control board and power The sous vide section's control has reported an electronic error.](https://stoverepair.center/error-codes/sks-f62/)
- [F-3 Knobs, keys and display The control thinks a key is stuck down.](https://stoverepair.center/error-codes/sks-f-3/)
- [F-9 Oven heating The oven cannot heat.](https://stoverepair.center/error-codes/sks-f-9/)
- [Loc Mode, not a failure Lock Out is on, so the oven door is locked and most controls will not start.](https://stoverepair.center/error-codes/sks-loc/)

[SKS stove repair](https://stoverepair.center/brands/sks/)

### ZLINE stove error codes 8 codes

- [F/1 Control board and power The main power board is misbehaving or the control boards have stopped talking.](https://stoverepair.center/error-codes/zline-f-1/)
- [F/3 Temperature sensor The temperature sensor inside an induction coil has failed or come loose.](https://stoverepair.center/error-codes/zline-f-3/)
- [F/4 Stovetop elements The power transistor that feeds an induction coil is failing; stop using the stove.](https://stoverepair.center/error-codes/zline-f-4/)
- [E/1 Stovetop elements One coil's temperature sensor is reading too much heat.](https://stoverepair.center/error-codes/zline-e-1/)
- [E/2 Stovetop elements The power transistor that drives a coil has become too hot.](https://stoverepair.center/error-codes/zline-e-2/)
- [E/3 Control board and power The voltage coming into the stove is higher than it can safely use.](https://stoverepair.center/error-codes/zline-e-3/)
- [E/4 Control board and power The voltage reaching the stove is too low for safe use.](https://stoverepair.center/error-codes/zline-e-4/)
- [E/5 Temperature sensor The temperature sensor on a coil has come loose or shifted out of place.](https://stoverepair.center/error-codes/zline-e-5/)

[ZLINE stove repair](https://stoverepair.center/brands/zline/)

### Café stove error codes 7 codes

- [F0 Knobs, keys and display GE's list links F0 to the touch keypanel, which often needs replacing.](https://stoverepair.center/error-codes/cafe-f0/)
- [F7 Knobs, keys and display A keypanel code: the touch pads are sending signals the control cannot use.](https://stoverepair.center/error-codes/cafe-f7/)
- [FD Temperature sensor The meat probe or the socket it plugs into may need replacing.](https://stoverepair.center/error-codes/cafe-fd/)
- [F97 Control board and power An internal component in the stove's electronics needs replacing.](https://stoverepair.center/error-codes/cafe-f97/)
- [F7X Control board and power A part inside the stove's electronics needs replacing.](https://stoverepair.center/error-codes/cafe-f7x/)
- [LOCK DOOR Door lock Self-clean has been chosen but the oven door is open.](https://stoverepair.center/error-codes/cafe-lock-door/)
- [Probe Mode, not a failure The probe is plugged in and the oven is waiting for a target temperature.](https://stoverepair.center/error-codes/cafe-probe/)

[Café stove repair](https://stoverepair.center/brands/cafe/)

### La Cornue stove error codes 7 codes

- [E2 Stovetop elements The induction electronics got too hot and switched the top off.](https://stoverepair.center/error-codes/la-cornue-e2/)
- [U400 Control board and power The stove is connected to the electrical supply the wrong way.](https://stoverepair.center/error-codes/la-cornue-u400/)
- [Er Stovetop elements The induction top found a problem inside the stove that the owner cannot correct.](https://stoverepair.center/error-codes/la-cornue-er/)
- [U Stovetop elements The plate cannot find a pan it is able to heat.](https://stoverepair.center/error-codes/la-cornue-u/)
- [E Stovetop elements The plate is reporting an electronic failure.](https://stoverepair.center/error-codes/la-cornue-e/)
- [H Mode, not a failure The zone you just turned off is still hot to the touch.](https://stoverepair.center/error-codes/la-cornue-h/)
- [L Mode, not a failure The lock is on, so the zones will not respond until it is released.](https://stoverepair.center/error-codes/la-cornue-l/)

[La Cornue stove repair](https://stoverepair.center/brands/la-cornue/)

### Fulgor Milano stove error codes 6 codes

- [F03 Door lock The oven door latch did not do what the control expected.](https://stoverepair.center/error-codes/fulgor-milano-f03/)
- [F15 Knobs, keys and display An oven knob was left between two positions for 30 seconds or longer.](https://stoverepair.center/error-codes/fulgor-milano-f15/)
- [F17 Knobs, keys and display A follow-on to F15, handled the same way.](https://stoverepair.center/error-codes/fulgor-milano-f17/)
- [F13 Mode, not a failure You picked a mode that cannot run with the meat probe plugged in.](https://stoverepair.center/error-codes/fulgor-milano-f13/)
- [Fan failure Control board and power The cooling fan that protects the electronics has a problem.](https://stoverepair.center/error-codes/fulgor-milano-fan-failure/)
- [L Mode, not a failure Control lock is switched on, so the zones ignore the knobs.](https://stoverepair.center/error-codes/fulgor-milano-l/)

[Fulgor Milano stove repair](https://stoverepair.center/brands/fulgor-milano/)

### Bertazzoni stove error codes 5 codes

- [H Mode, not a failure The zone is switched off but the glass over it is still very hot.](https://stoverepair.center/error-codes/bertazzoni-h/)
- [L Mode, not a failure The zones are locked so they cannot be turned on by accident.](https://stoverepair.center/error-codes/bertazzoni-l/)
- [A Mode, not a failure The heating accelerator is running the zone at peak power for a while.](https://stoverepair.center/error-codes/bertazzoni-a/)
- [P Mode, not a failure Power mode is running the zone at full output for up to ten minutes.](https://stoverepair.center/error-codes/bertazzoni-p/)
- [Showroom Mode, not a failure The retailer's showroom setting may be switched on, so the display works without heat.](https://stoverepair.center/error-codes/bertazzoni-showroom/)

[Bertazzoni stove repair](https://stoverepair.center/brands/bertazzoni/)

### Monogram stove error codes 5 codes

- [err turn surf frnr off Mode, not a failure A burner was turned on while the oven is self-cleaning.](https://stoverepair.center/error-codes/monogram-err-turn-surf-frnr-off/)
- [F- and a number Control board and power The oven control has recorded a function error.](https://stoverepair.center/error-codes/monogram-f-and-a-number/)
- [Close door Door lock Self-clean has been selected with the oven door open.](https://stoverepair.center/error-codes/monogram-close-door/)
- [SET PROBE Mode, not a failure The probe is plugged in and the oven wants a target food temperature.](https://stoverepair.center/error-codes/monogram-set-probe/)
- [Flashing oven knob Mode, not a failure The oven is preheating; the lit knob goes solid when it is ready.](https://stoverepair.center/error-codes/monogram-flashing-oven-knob/)

[Monogram stove repair](https://stoverepair.center/brands/monogram/)

### Fisher & Paykel stove error codes 4 codes

- [A1 Oven heating The oven has overheated.](https://stoverepair.center/error-codes/fisher-and-paykel-a1/)
- [A2 Door lock The door could not lock after you started Self Clean.](https://stoverepair.center/error-codes/fisher-and-paykel-a2/)
- [A3 Door lock The door will not unlock after Self Clean finished.](https://stoverepair.center/error-codes/fisher-and-paykel-a3/)
- [F Control board and power The oven found a technical problem it cannot fix itself.](https://stoverepair.center/error-codes/fisher-and-paykel-f/)

[Fisher & Paykel stove repair](https://stoverepair.center/brands/fisher-and-paykel/)

### Smeg stove error codes 2 codes

- [ERR Control board and power The oven's electronic control has flagged a problem Smeg does not spell out.](https://stoverepair.center/error-codes/smeg-err/)
- [Pre-heating light flashing Mode, not a failure The oven has reached its heat and is cycling to hold it.](https://stoverepair.center/error-codes/smeg-pre-heating-light-flashing/)

[Smeg stove repair](https://stoverepair.center/brands/smeg/)

### Only confirmed codes

Every code here is taken from the manufacturer's own documentation, never from a forum or a parts listing. If yours is not listed, book with the exact characters and the full model number, and we will tell you whether it is one we take.

## Three things before you look it up.

A code is a lead, not a verdict. These decide whether the answer you find will be any use.

01

### Every letter and digit on the display

Write the code down in order and note whether it flashes, beeps or sits beside the clock. Snap a photo first, because pressing a key or flipping the breaker can make it disappear.

02

### The model number from the stove's plate

Look behind the storage drawer or around the oven door opening. One code can mean an oven sensor on one make and a stuck key on another.

03

### Is there a gas smell, smoke or a hot-wire smell?

If there is, you leave the stove alone and get outside now. If not, the next open appointment is soon enough.

## What each kind of code means.

Codes fall into a handful of families. The family says more about the likely repair than the characters do — and one of them is not a repair at all.

[How to read a code](https://stoverepair.center/problems/stove-error-code/)

### Mode, not a failure

56 codes

Something the stove was switched into, often by accident, rather than something that broke: a control lock pressed while wiping the panel, a Sabbath setting, a showroom demo mode that lights the display and heats nothing, a reminder that a spot on the stovetop is still hot. No part is worn out, and the stove's own keys put it right.

[S](https://stoverepair.center/error-codes/aga-s/) [H](https://stoverepair.center/error-codes/aga-h/) [H](https://stoverepair.center/error-codes/bertazzoni-h/) [L](https://stoverepair.center/error-codes/bertazzoni-l/) [A](https://stoverepair.center/error-codes/bertazzoni-a/) [P](https://stoverepair.center/error-codes/bertazzoni-p/) [Showroom](https://stoverepair.center/error-codes/bertazzoni-showroom/) [ERR/toP](https://stoverepair.center/error-codes/bosch-err-top/) [dE](https://stoverepair.center/error-codes/bosch-de/) [F8](https://stoverepair.center/error-codes/bosch-f8/) [Probe](https://stoverepair.center/error-codes/cafe-probe/) [5d](https://stoverepair.center/error-codes/electrolux-5d/) [F13](https://stoverepair.center/error-codes/fulgor-milano-f13/) [L](https://stoverepair.center/error-codes/fulgor-milano-l/) [HOT](https://stoverepair.center/error-codes/ge-profile-hot/) [LOC](https://stoverepair.center/error-codes/ge-loc/) [OFF](https://stoverepair.center/error-codes/ge-off/) [⊃](https://stoverepair.center/error-codes/ge-backward-c/) [ER04](https://stoverepair.center/error-codes/hestan-er04/) [U](https://stoverepair.center/error-codes/ilve-u/) [H](https://stoverepair.center/error-codes/ilve-h/) [LLLL](https://stoverepair.center/error-codes/ilve-llll/) [ES](https://stoverepair.center/error-codes/jennair-es/) [F0E0](https://stoverepair.center/error-codes/kitchenaid-f0e0/) [Blinking Start button](https://stoverepair.center/error-codes/kitchenaid-blinking-start-button/) [Solid Start light](https://stoverepair.center/error-codes/kitchenaid-solid-start-light/) [H](https://stoverepair.center/error-codes/la-cornue-h/) [L](https://stoverepair.center/error-codes/la-cornue-l/) [HS](https://stoverepair.center/error-codes/lg-hs/) [PF](https://stoverepair.center/error-codes/lg-pf/) [Sb](https://stoverepair.center/error-codes/lg-sb/) [ES](https://stoverepair.center/error-codes/maytag-es/) [Sab](https://stoverepair.center/error-codes/maytag-sab/) [Probe](https://stoverepair.center/error-codes/maytag-probe/) [POWER LOSS](https://stoverepair.center/error-codes/maytag-power-loss/) [Demo Mode](https://stoverepair.center/error-codes/miele-demo-mode/) [Maximum operating duration reached](https://stoverepair.center/error-codes/miele-maximum-operating-duration-reached/) [Power failure - Program cancelled](https://stoverepair.center/error-codes/miele-power-failure-program-cancelled/) [System Lock](https://stoverepair.center/error-codes/miele-system-lock/) [12:00](https://stoverepair.center/error-codes/miele-12-00/) [err turn surf frnr off](https://stoverepair.center/error-codes/monogram-err-turn-surf-frnr-off/) [SET PROBE](https://stoverepair.center/error-codes/monogram-set-probe/) [Flashing oven knob](https://stoverepair.center/error-codes/monogram-flashing-oven-knob/) [tESt](https://stoverepair.center/error-codes/samsung-test/) [-dE-](https://stoverepair.center/error-codes/samsung-de/) [Cooktop in use](https://stoverepair.center/error-codes/samsung-cooktop-in-use/) [C-10](https://stoverepair.center/error-codes/samsung-c-10/) [Loc](https://stoverepair.center/error-codes/sks-loc/) [Pre-heating light flashing](https://stoverepair.center/error-codes/smeg-pre-heating-light-flashing/) [dE](https://stoverepair.center/error-codes/thermador-de/) [F8](https://stoverepair.center/error-codes/thermador-f8/) [H](https://stoverepair.center/error-codes/whirlpool-h/) [PUSH](https://stoverepair.center/error-codes/whirlpool-push/) [Lo](https://stoverepair.center/error-codes/whirlpool-lo/) [DEMO MODE](https://stoverepair.center/error-codes/whirlpool-demo-mode/) [PF](https://stoverepair.center/error-codes/wolf-pf/)

Usually leads to

No repair — the setting is changed back

Shows up as

[Stove Display Blank or Flashing](https://stoverepair.center/problems/stove-display-blank-or-flashing/) [Stove Won't Turn On](https://stoverepair.center/problems/stove-wont-turn-on/) [Oven on My Stove Won't Heat Up](https://stoverepair.center/problems/stove-oven-not-heating/) [Stove Error Code](https://stoverepair.center/problems/stove-error-code/)

### Ignition and burners

2 codes

The stove asked a gas burner or the oven to light and never saw a flame, or it kept sparking once the flame was already burning. A burner cap sitting off-center and an igniter still wet from cleaning are ruled out before the spark switch, the spark module or a valve is replaced. A smell of gas outranks every code on the display: get everyone out, and call the gas utility once you are outside.

[ER01](https://stoverepair.center/error-codes/hestan-er01/) [ER05](https://stoverepair.center/error-codes/hestan-er05/)

Usually leads to

[Igniter and spark switch repair](https://stoverepair.center/services/igniter-and-spark-switch-repair/)

Shows up as

[Gas Stove Won't Light](https://stoverepair.center/problems/gas-stove-wont-light/) [Stove Clicking](https://stoverepair.center/problems/stove-clicking/) [Stove Burner Not Working](https://stoverepair.center/problems/stove-burner-not-working/) [Stove Smells Like Gas](https://stoverepair.center/problems/stove-smells-like-gas/)

### Stovetop elements

32 codes

A burner on an electric or induction stovetop did not heat the way the knob or key asked, heated with nothing set, or ran hotter than the setting. The pan, a lock left on and the switch behind the knob are checked before the element under the glass, its limiter or an induction board is changed. If a burner keeps heating after it has been switched off, turn the stove's breaker off before anything else.

[E2](https://stoverepair.center/error-codes/aga-e2/) [Er](https://stoverepair.center/error-codes/aga-er/) [E2](https://stoverepair.center/error-codes/bluestar-e2/) [F1](https://stoverepair.center/error-codes/bosch-f1/) [F2](https://stoverepair.center/error-codes/bosch-f2/) [F5](https://stoverepair.center/error-codes/bosch-f5/) [F40](https://stoverepair.center/error-codes/electrolux-f40/) [F40](https://stoverepair.center/error-codes/frigidaire-f40/) [Flashing power setting](https://stoverepair.center/error-codes/ge-profile-flashing-power-setting/) [E2](https://stoverepair.center/error-codes/hestan-e2/) [E](https://stoverepair.center/error-codes/ilve-e/) [C81](https://stoverepair.center/error-codes/jennair-c81/) [H](https://stoverepair.center/error-codes/kenmore-h/) [E2](https://stoverepair.center/error-codes/la-cornue-e2/) [Er](https://stoverepair.center/error-codes/la-cornue-er/) [U](https://stoverepair.center/error-codes/la-cornue-u/) [E](https://stoverepair.center/error-codes/la-cornue-e/) [F33](https://stoverepair.center/error-codes/lg-f33/) [F51](https://stoverepair.center/error-codes/lg-f51/) [Underlined u](https://stoverepair.center/error-codes/samsung-underlined-u/) [F1~F15](https://stoverepair.center/error-codes/sks-f1-f15/) [F33~F45](https://stoverepair.center/error-codes/sks-f33-f45/) [F51~F59](https://stoverepair.center/error-codes/sks-f51-f59/) [F1](https://stoverepair.center/error-codes/thermador-f1/) [F2](https://stoverepair.center/error-codes/thermador-f2/) [F4](https://stoverepair.center/error-codes/thermador-f4/) [F5](https://stoverepair.center/error-codes/thermador-f5/) [C81](https://stoverepair.center/error-codes/whirlpool-c81/) [E2](https://stoverepair.center/error-codes/wolf-e2/) [F/4](https://stoverepair.center/error-codes/zline-f-4/) [E/1](https://stoverepair.center/error-codes/zline-e-1/) [E/2](https://stoverepair.center/error-codes/zline-e-2/)

Usually leads to

[Glass stovetop repair](https://stoverepair.center/services/glass-stovetop-repair/)

Shows up as

[Stovetop Not Heating](https://stoverepair.center/problems/stovetop-not-heating/) [Stove Burner Not Working](https://stoverepair.center/problems/stove-burner-not-working/) [Stove Burner Stays on High](https://stoverepair.center/problems/stove-burner-stays-on-high/) [Stove Error Code](https://stoverepair.center/problems/stove-error-code/)

### Oven heating

26 codes

The oven part of the stove was set to bake or broil and did not warm the way the controls expected, or took far too long to get there. On an electric stove a bake or broil element that has burned through is the everyday reason; on a gas stove the oven igniter and the valve it opens are looked at first. The wiring and the relay on the board are checked before the board itself is blamed.

[010-014](https://stoverepair.center/error-codes/aga-010-014/) [130-136](https://stoverepair.center/error-codes/aga-130-136/) [F80](https://stoverepair.center/error-codes/bluestar-f80/) [C-21](https://stoverepair.center/error-codes/dacor-c-21/) [C-24](https://stoverepair.center/error-codes/dacor-c-24/) [F10](https://stoverepair.center/error-codes/electrolux-f10/) [A1](https://stoverepair.center/error-codes/fisher-and-paykel-a1/) [F10](https://stoverepair.center/error-codes/frigidaire-f10/) [F2](https://stoverepair.center/error-codes/ge-f2/) [F5E5](https://stoverepair.center/error-codes/jennair-f5e5/) [E1](https://stoverepair.center/error-codes/kenmore-e1/) [E3](https://stoverepair.center/error-codes/kenmore-e3/) [E5](https://stoverepair.center/error-codes/kenmore-e5/) [E03](https://stoverepair.center/error-codes/kenmore-e03/) [F9](https://stoverepair.center/error-codes/lg-f9/) [F17](https://stoverepair.center/error-codes/lg-f17/) [C-21](https://stoverepair.center/error-codes/samsung-c-21/) [C-24](https://stoverepair.center/error-codes/samsung-c-24/) [C-25](https://stoverepair.center/error-codes/samsung-c-25/) [F-9](https://stoverepair.center/error-codes/sks-f-9/) [FEE6](https://stoverepair.center/error-codes/whirlpool-fee6/) [FEE7](https://stoverepair.center/error-codes/whirlpool-fee7/) [F5 E5](https://stoverepair.center/error-codes/whirlpool-f5-e5/) [02](https://stoverepair.center/error-codes/wolf-02/) [0E](https://stoverepair.center/error-codes/wolf-0e/) [0221](https://stoverepair.center/error-codes/wolf-0221/)

Usually leads to

[Stove oven heating repair](https://stoverepair.center/services/stove-oven-heating-repair/)

Shows up as

[Oven on My Stove Won't Heat Up](https://stoverepair.center/problems/stove-oven-not-heating/) [Oven on My Stove Runs Hot or Cold](https://stoverepair.center/problems/stove-oven-temperature-off/) [Stove Smoking](https://stoverepair.center/problems/stove-smoking/) [Stove Error Code](https://stoverepair.center/problems/stove-error-code/)

### Temperature sensor

34 codes

The thin probe on the back wall of the oven sent the stove a reading it would not trust, or one that kept climbing past the setting. A loose plug behind the stove or a probe knocked against the racks is ruled out before the sensor or the board is replaced. If the oven keeps getting hotter with the controls turned off, switch the stove off at its breaker first.

[007](https://stoverepair.center/error-codes/aga-007/) [020-024](https://stoverepair.center/error-codes/aga-020-024/) [060-100](https://stoverepair.center/error-codes/aga-060-100/) [F40](https://stoverepair.center/error-codes/bluestar-f40/) [F50](https://stoverepair.center/error-codes/bluestar-f50/) [e101](https://stoverepair.center/error-codes/bosch-e101/) [FD](https://stoverepair.center/error-codes/cafe-fd/) [C-20](https://stoverepair.center/error-codes/dacor-c-20/) [C-23](https://stoverepair.center/error-codes/dacor-c-23/) [C-70](https://stoverepair.center/error-codes/dacor-c-70/) [F30](https://stoverepair.center/error-codes/electrolux-f30/) [F30](https://stoverepair.center/error-codes/frigidaire-f30/) [F31](https://stoverepair.center/error-codes/frigidaire-f31/) [F4](https://stoverepair.center/error-codes/ge-profile-f4/) [F3](https://stoverepair.center/error-codes/ge-f3/) [E9](https://stoverepair.center/error-codes/hestan-e9/) [E9](https://stoverepair.center/error-codes/ilve-e9/) [F3E0](https://stoverepair.center/error-codes/jennair-f3e0/) [F3E4](https://stoverepair.center/error-codes/jennair-f3e4/) [E0](https://stoverepair.center/error-codes/kenmore-e0/) [E02](https://stoverepair.center/error-codes/kenmore-e02/) [F3 E3](https://stoverepair.center/error-codes/kitchenaid-f3-e3/) [F1](https://stoverepair.center/error-codes/lg-f1/) [F4](https://stoverepair.center/error-codes/lg-f4/) [F8](https://stoverepair.center/error-codes/lg-f8/) [3d11](https://stoverepair.center/error-codes/maytag-3d11/) [No signal to the probe](https://stoverepair.center/error-codes/miele-no-signal-to-the-probe/) [C-20](https://stoverepair.center/error-codes/samsung-c-20/) [F3 E0](https://stoverepair.center/error-codes/whirlpool-f3-e0/) [03](https://stoverepair.center/error-codes/wolf-03/) [04](https://stoverepair.center/error-codes/wolf-04/) [09](https://stoverepair.center/error-codes/wolf-09/) [F/3](https://stoverepair.center/error-codes/zline-f-3/) [E/5](https://stoverepair.center/error-codes/zline-e-5/)

Usually leads to

[Stove oven heating repair](https://stoverepair.center/services/stove-oven-heating-repair/)

Shows up as

[Oven on My Stove Runs Hot or Cold](https://stoverepair.center/problems/stove-oven-temperature-off/) [Oven on My Stove Won't Heat Up](https://stoverepair.center/problems/stove-oven-not-heating/) [Stove Error Code](https://stoverepair.center/problems/stove-error-code/)

### Door lock

31 codes

The latch that holds the oven door shut during self-clean did not move where the stove told it to, or its switch reported the wrong position. It turns up most often during or right after a self-clean cycle, or once the door has been lifted off for cleaning. The latch, its switches, the hinges and how squarely the door closes are checked before the lock motor is changed.

[e126](https://stoverepair.center/error-codes/bosch-e126/) [LOCK DOOR](https://stoverepair.center/error-codes/cafe-lock-door/) [C-d1](https://stoverepair.center/error-codes/dacor-c-d1/) [F90](https://stoverepair.center/error-codes/electrolux-f90/) [A2](https://stoverepair.center/error-codes/fisher-and-paykel-a2/) [A3](https://stoverepair.center/error-codes/fisher-and-paykel-a3/) [F90](https://stoverepair.center/error-codes/frigidaire-f90/) [F03](https://stoverepair.center/error-codes/fulgor-milano-f03/) [FC](https://stoverepair.center/error-codes/ge-profile-fc/) [DOOR LOCKING](https://stoverepair.center/error-codes/ge-profile-door-locking/) [F9](https://stoverepair.center/error-codes/ge-f9/) [Unlock Door](https://stoverepair.center/error-codes/ge-unlock-door/) [Loc Door](https://stoverepair.center/error-codes/ge-loc-door/) [F5E0](https://stoverepair.center/error-codes/jennair-f5e0/) [F7E0](https://stoverepair.center/error-codes/jennair-f7e0/) [F9-1](https://stoverepair.center/error-codes/jennair-f9-1/) [E2](https://stoverepair.center/error-codes/kenmore-e2/) [E10](https://stoverepair.center/error-codes/kenmore-e10/) [E16](https://stoverepair.center/error-codes/kenmore-e16/) [LOC](https://stoverepair.center/error-codes/kenmore-loc/) [F5 E0](https://stoverepair.center/error-codes/kitchenaid-f5-e0/) [LOC](https://stoverepair.center/error-codes/kitchenaid-loc/) [F10](https://stoverepair.center/error-codes/lg-f10/) [F9-1](https://stoverepair.center/error-codes/maytag-f9-1/) [F7 E0](https://stoverepair.center/error-codes/maytag-f7-e0/) [F32](https://stoverepair.center/error-codes/miele-f32/) [F33](https://stoverepair.center/error-codes/miele-f33/) [Close door](https://stoverepair.center/error-codes/monogram-close-door/) [C-d1](https://stoverepair.center/error-codes/samsung-c-d1/) [door](https://stoverepair.center/error-codes/samsung-door/) [01](https://stoverepair.center/error-codes/wolf-01/)

Usually leads to

[Stove door and hinge repair](https://stoverepair.center/services/stove-door-and-hinge-repair/)

Shows up as

[Stove Door Won't Close](https://stoverepair.center/problems/stove-door-wont-close/) [Oven on My Stove Won't Heat Up](https://stoverepair.center/problems/stove-oven-not-heating/) [Stove Error Code](https://stoverepair.center/problems/stove-error-code/)

### Knobs, keys and display

29 codes

A key on the panel was held down too long, reported a press nobody made, or stopped answering; or a knob's switch told the stove it was on when it was off. Water, a spill or grease worked in behind a knob is ruled out first, then the switch, the key panel and the cable to the board. If a burner keeps heating while the keys or knobs do nothing, switch the stove off at the breaker.

[FE](https://stoverepair.center/error-codes/aga-fe/) [139](https://stoverepair.center/error-codes/aga-139/) [159](https://stoverepair.center/error-codes/aga-159/) [e011](https://stoverepair.center/error-codes/bosch-e011/) [F0](https://stoverepair.center/error-codes/cafe-f0/) [F7](https://stoverepair.center/error-codes/cafe-f7/) [C-d0](https://stoverepair.center/error-codes/dacor-c-d0/) [C-F2](https://stoverepair.center/error-codes/dacor-c-f2/) [F1](https://stoverepair.center/error-codes/electrolux-f1/) [F1](https://stoverepair.center/error-codes/frigidaire-f1/) [F15](https://stoverepair.center/error-codes/fulgor-milano-f15/) [F17](https://stoverepair.center/error-codes/fulgor-milano-f17/) [F6](https://stoverepair.center/error-codes/ge-profile-f6/) [F1](https://stoverepair.center/error-codes/ge-f1/) [ERR](https://stoverepair.center/error-codes/ge-err/) [Er 03](https://stoverepair.center/error-codes/hestan-er-03/) [F2E0](https://stoverepair.center/error-codes/jennair-f2e0/) [Blinking amber lights](https://stoverepair.center/error-codes/jennair-blinking-amber-lights/) [F2 E0](https://stoverepair.center/error-codes/kitchenaid-f2-e0/) [F3](https://stoverepair.center/error-codes/lg-f3/) [1c1c](https://stoverepair.center/error-codes/maytag-1c1c/) [Lock](https://stoverepair.center/error-codes/maytag-lock/) [C-d0](https://stoverepair.center/error-codes/samsung-c-d0/) [F-3](https://stoverepair.center/error-codes/sks-f-3/) [E7010](https://stoverepair.center/error-codes/thermador-e7010/) [F2 E1](https://stoverepair.center/error-codes/whirlpool-f2-e1/) [F6 E5](https://stoverepair.center/error-codes/whirlpool-f6-e5/) [Flashing indicator light](https://stoverepair.center/error-codes/whirlpool-flashing-indicator-light/) [ERR OC](https://stoverepair.center/error-codes/wolf-err-oc/)

Usually leads to

[Knob and switch replacement](https://stoverepair.center/services/knob-and-switch-replacement/)

Shows up as

[Stove Knob Broken or Loose](https://stoverepair.center/problems/stove-knob-broken-or-loose/) [Stove Display Blank or Flashing](https://stoverepair.center/problems/stove-display-blank-or-flashing/) [Stove Burner Stays on High](https://stoverepair.center/problems/stove-burner-stays-on-high/) [Stove Error Code](https://stoverepair.center/problems/stove-error-code/)

### Control board and power

79 codes

The main board failed its own start-up check, lost contact with the display, or saw the supply voltage sag too low, often after a storm, a power outage or a spill that ran down behind the panel. The breaker, the cord and the outlet are ruled out before a board is replaced. A stove that sparks, smells of hot wiring or keeps heating while this code shows is switched off at the breaker first.

[CE](https://stoverepair.center/error-codes/aga-ce/) [110-116](https://stoverepair.center/error-codes/aga-110-116/) [U400](https://stoverepair.center/error-codes/aga-u400/) [F20](https://stoverepair.center/error-codes/bluestar-f20/) [F60](https://stoverepair.center/error-codes/bluestar-f60/) [E6](https://stoverepair.center/error-codes/bluestar-e6/) [E8](https://stoverepair.center/error-codes/bluestar-e8/) [Er47](https://stoverepair.center/error-codes/bluestar-er47/) [e005](https://stoverepair.center/error-codes/bosch-e005/) [E100](https://stoverepair.center/error-codes/bosch-e100/) [E302](https://stoverepair.center/error-codes/bosch-e302/) [e310](https://stoverepair.center/error-codes/bosch-e310/) [E9000](https://stoverepair.center/error-codes/bosch-e9000/) [E9011](https://stoverepair.center/error-codes/bosch-e9011/) [F97](https://stoverepair.center/error-codes/cafe-f97/) [F7X](https://stoverepair.center/error-codes/cafe-f7x/) [C-F0](https://stoverepair.center/error-codes/dacor-c-f0/) [C-31](https://stoverepair.center/error-codes/dacor-c-31/) [C-A2](https://stoverepair.center/error-codes/dacor-c-a2/) [Err](https://stoverepair.center/error-codes/electrolux-err/) [F3](https://stoverepair.center/error-codes/electrolux-f3/) [F](https://stoverepair.center/error-codes/fisher-and-paykel-f/) [F3](https://stoverepair.center/error-codes/frigidaire-f3/) [F12](https://stoverepair.center/error-codes/frigidaire-f12/) [F13](https://stoverepair.center/error-codes/frigidaire-f13/) [Fan failure](https://stoverepair.center/error-codes/fulgor-milano-fan-failure/) [F8](https://stoverepair.center/error-codes/ge-profile-f8/) [F350](https://stoverepair.center/error-codes/ge-profile-f350/) [F5](https://stoverepair.center/error-codes/ge-f5/) [FF](https://stoverepair.center/error-codes/ge-ff/) [F96](https://stoverepair.center/error-codes/ge-f96/) [Bad Line](https://stoverepair.center/error-codes/ge-bad-line/) [ERR04](https://stoverepair.center/error-codes/hestan-err04/) [ER06](https://stoverepair.center/error-codes/hestan-er06/) [Er 47](https://stoverepair.center/error-codes/hestan-er-47/) [E6](https://stoverepair.center/error-codes/hestan-e6/) [E8](https://stoverepair.center/error-codes/hestan-e8/) [U 400](https://stoverepair.center/error-codes/hestan-u-400/) [E47](https://stoverepair.center/error-codes/ilve-e47/) [E5](https://stoverepair.center/error-codes/ilve-e5/) [F](https://stoverepair.center/error-codes/ilve-f/) [F1E1](https://stoverepair.center/error-codes/jennair-f1e1/) [F8E0](https://stoverepair.center/error-codes/jennair-f8e0/) [F0E0](https://stoverepair.center/error-codes/jennair-f0e0/) [F6E1](https://stoverepair.center/error-codes/jennair-f6e1/) [Er-](https://stoverepair.center/error-codes/kenmore-er/) [E8](https://stoverepair.center/error-codes/kenmore-e8/) [E17](https://stoverepair.center/error-codes/kenmore-e17/) [Blinking amber lights](https://stoverepair.center/error-codes/kitchenaid-blinking-amber-lights/) [F9E0](https://stoverepair.center/error-codes/kitchenaid-f9e0/) [F7 E5](https://stoverepair.center/error-codes/kitchenaid-f7-e5/) [1c31](https://stoverepair.center/error-codes/kitchenaid-1c31/) [U400](https://stoverepair.center/error-codes/la-cornue-u400/) [F11](https://stoverepair.center/error-codes/lg-f11/) [F27](https://stoverepair.center/error-codes/lg-f27/) [F42](https://stoverepair.center/error-codes/lg-f42/) [F8 E2](https://stoverepair.center/error-codes/maytag-f8-e2/) [Call Service](https://stoverepair.center/error-codes/maytag-call-service/) [4d21](https://stoverepair.center/error-codes/maytag-4d21/) [F- and a number](https://stoverepair.center/error-codes/monogram-f-and-a-number/) [C-30](https://stoverepair.center/error-codes/samsung-c-30/) [C-F0](https://stoverepair.center/error-codes/samsung-c-f0/) [bAd LinE](https://stoverepair.center/error-codes/samsung-bad-line/) [F1~F25](https://stoverepair.center/error-codes/sks-f1-f25/) [F62](https://stoverepair.center/error-codes/sks-f62/) [ERR](https://stoverepair.center/error-codes/smeg-err/) [E](https://stoverepair.center/error-codes/thermador-e/) [E0211](https://stoverepair.center/error-codes/thermador-e0211/) [E9000](https://stoverepair.center/error-codes/thermador-e9000/) [F8 E0](https://stoverepair.center/error-codes/whirlpool-f8-e0/) [F1 E7](https://stoverepair.center/error-codes/whirlpool-f1-e7/) [10](https://stoverepair.center/error-codes/wolf-10/) [3C20](https://stoverepair.center/error-codes/wolf-3c20/) [5521](https://stoverepair.center/error-codes/wolf-5521/) [E6](https://stoverepair.center/error-codes/wolf-e6/) [U400](https://stoverepair.center/error-codes/wolf-u400/) [F/1](https://stoverepair.center/error-codes/zline-f-1/) [E/3](https://stoverepair.center/error-codes/zline-e-3/) [E/4](https://stoverepair.center/error-codes/zline-e-4/)

Usually leads to

[Control board and display repair](https://stoverepair.center/services/control-board-and-display-repair/)

Shows up as

[Stove Display Blank or Flashing](https://stoverepair.center/problems/stove-display-blank-or-flashing/) [Stove Won't Turn On](https://stoverepair.center/problems/stove-wont-turn-on/) [Stove Sparking](https://stoverepair.center/problems/stove-sparking/) [Stove Error Code](https://stoverepair.center/problems/stove-error-code/)

For the heart of your home.

## Questions about the codes.

### The code on my stove is not on this site. What now?

It only means we have not written that code up yet; a code gets a page once the maker's own manual explains it. Copy the characters, note whether they flash and where on the display they sit, and type them into the booking form so the technician can match them to your model.

### Does a stove code mean the same thing on every brand?

No. A code that points to the oven sensor on one make can mean a stuck key or a door lock on another, and some makers changed their codes between model years. A stove code only makes sense next to the brand and, often, the full model number.

### Can I reset a stove code myself?

Some codes clear after the stove's breaker has been off for a few minutes, and one that stays away was probably a blip in the power. A code that comes back every time is pointing at a real problem. If a burner or the oven keeps heating while the code shows, leave the breaker off and book instead of trying again.

### My stove shows a code but still cooks. Is anything broken?

Maybe not. Several codes owners look up are settings rather than failures, such as a control lock, a Sabbath or demo mode, or a hot-surface reminder, and none of them needs a part. Each code page says when that is the case and how to switch it back.

---

**[Read on the site: Stove Error Codes — What They Mean | StoveRepair.center](https://stoverepair.center/error-codes/)**

**[Book a visit with StoveRepair.center](https://stoverepair.center/schedule/)**